Jump to contentJump to page navigation: previous page [access key p]/next page [access key n]
documentation.suse.com / SUSE Linux Enterprise Server Documentation / Virtualization Guide / Managing Virtual Machines with Xen / Administrative Tasks
Applies to SUSE Linux Enterprise Server 15 SP2

26 Administrative Tasks

  

26.1 The Boot Loader Program

  

The boot loader controls how the virtualization software boots and runs. You can modify the boot loader properties by using YaST, or by directly editing the boot loader configuration file.

The YaST boot loader program is located at YaST › System › Boot Loader. Click the Bootloader Options tab and select the line containing the Xen kernel as the Default Boot Section.

Boot Loader Settings
Figure 26.1: Boot Loader Settings
  

Confirm with OK. Next time you boot the host, it will be ready to provide the Xen virtualization environment.

You can use the Boot Loader program to specify functionality, such as:

You can customize your virtualization environment by editing the /etc/default/grub file. Add the following line to this file: GRUB_CMDLINE_XEN="<boot_parameters>". Do not forget to run grub2-mkconfig -o /boot/grub2/grub.cfg after editing the file.

26.2 Sparse Image Files and Disk Space

  

If the host’s physical disk reaches a state where it has no available space, a virtual machine using a virtual disk based on a sparse image file cannot write to its disk. Consequently, it reports I/O errors.

If this situation occurs, you should free up available space on the physical disk, remount the virtual machine’s file system, and set the file system back to read-write.

To check the actual disk requirements of a sparse image file, use the command du -h <image file>.

To increase the available space of a sparse image file, first increase the file size and then the file system.

Warning
Warning: Back Up Before Resizing

Touching the sizes of partitions or sparse files always bears the risk of data failure. Do not work without a backup.

The resizing of the image file can be done online, while the VM Guest is running. Increase the size of a sparse image file with: 

> sudo dd if=/dev/zero of=<image file> count=0 bs=1M seek=<new size in MB>

For example, to increase the file /var/lib/xen/images/sles/disk0 to a size of 16GB, use the command: 

> sudo dd if=/dev/zero of=/var/lib/xen/images/sles/disk0 count=0 bs=1M seek=16000
Note
Note: Increasing Non-Sparse Images

It is also possible to increase the image files of devices that are not sparse files. However, you must know exactly where the previous image ends. Use the seek parameter to point to the end of the image file and use a command similar to the following: 

> sudo dd if=/dev/zero of=/var/lib/xen/images/sles/disk0 seek=8000 bs=1M count=2000

Be sure to use the right seek, else data loss may happen.

If the VM Guest is running during the resize operation, also resize the loop device that provides the image file to the VM Guest. First detect the correct loop device with the command: 

> sudo losetup -j /var/lib/xen/images/sles/disk0

Then resize the loop device, for example /dev/loop0, with the following command: 

> sudo losetup -c /dev/loop0

Finally check the size of the block device inside the guest system with the command fdisk -l /dev/xvdb. The device name depends on the actually increased device.

The resizing of the file system inside the sparse file involves tools that are depending on the actual file system. This is described in detail in the Storage Administration Guide.

26.3 Migrating Xen VM Guest Systems

  

With Xen it is possible to migrate a VM Guest system from one VM Host Server to another with almost no service interruption. This could be used for example to move a busy VM Guest to a VM Host Server that has stronger hardware or is not yet loaded. Or, if a service of a VM Host Server is required, all VM Guest systems running on this machine can be migrated to other machines to avoid interruption of service. These are only two examples—many more reasons may apply to your personal situation.

Before starting, some preliminary considerations regarding the VM Host Server should be taken into account:

  • All VM Host Server systems should use a similar CPU. The frequency is not so important, but they should be using the same CPU family. To get more information about the used CPU, use cat /proc/cpuinfo. Find more details about comparing host CPU features in Section 26.3.1, “Detecting CPU Features”.

  • All resources that are used by a specific guest system must be available on all involved VM Host Server systems—for example all used block devices must exist on both VM Host Server systems.

  • If the hosts included in the migration process run in different subnets, make sure that either DHCP relay is available to the guests, or for guests with static network configuration, set up the network manually.

  • Using special features like PCI Pass-Through may be problematic. Do not implement these when deploying for an environment that should migrate VM Guest systems between different VM Host Server systems.

  • For fast migrations, a fast network is mandatory. If possible, use GB Ethernet and fast switches. Deploying VLAN might also help avoid collisions.

26.3.1 Detecting CPU Features

  

By using the cpuid and xen_maskcalc.py tools, you can compare features of a CPU on the host from where you are migrating the source VM Guest with the features of CPUs on the target hosts. This way you can better predict if the guest migrations will be successful.

  1. Run the cpuid -1r command on each Dom0 that is supposed to run or receive the migrated VM Guest and capture the output in text files, for example: 

    tux@vm_host1 > sudo cpuid -1r > vm_host1.txt
tux@vm_host2 > sudo cpuid -1r > vm_host2.txt
tux@vm_host3 > sudo cpuid -1r > vm_host3.txt

  2. Copy all the output text files on a host with the xen_maskcalc.py script installed.

  3. Run the xen_maskcalc.py script on all output text files: 

    > sudo xen_maskcalc.py vm_host1.txt vm_host2.txt vm_host3.txt
cpuid = [
    "0x00000001:ecx=x00xxxxxx0xxxxxxxxx00xxxxxxxxxxx",
    "0x00000007,0x00:ebx=xxxxxxxxxxxxxxxxxx00x0000x0x0x00"
]

  4. Copy the output cpuid=[...] configuration snipped into the xl configuration of the migrated guestdomU.cfg or alternatively to its libvirt's XML configuration.

  5. Start the source guest with the trimmed CPU configuration. The guest can now only use CPU features which are present on each of the hosts.

Tip
Tip

libvirt also supports calculating a baseline CPU for migration. For more details, refer to https://documentation.suse.com/sles/15-SP2/html/SLES-all/article-vt-best-practices.html.

26.3.1.1 For More Information

  

You can find more details about cpuid at http://etallen.com/cpuid.html.

You can download the latest version of the CPU mask calculator from https://github.com/twizted/xen_maskcalc.

26.3.2 Preparing Block Devices for Migrations

  

The block devices needed by the VM Guest system must be available on all involved VM Host Server systems. This is done by implementing some kind of shared storage that serves as container for the root file system of the migrated VM Guest system. Common possibilities include:

  • iSCSI can be set up to give access to the same block devices from different systems at the same time. For more information about iSCSI, see Chapter 15, Mass Storage over IP Networks: iSCSI.

  • NFS is a widely used root file system that can easily be accessed from different locations. For more information, see Chapter 33, Sharing File Systems with NFS.

  • DRBD can be used if only two VM Host Server systems are involved. This gives some extra data security, because the used data is mirrored over the network. For more information, see the SUSE Linux Enterprise High Availability 15 SP2 documentation at https://documentation.suse.com/sle-ha/15-SP2/.

  • SCSI can also be used if the available hardware permits shared access to the same disks.

  • NPIV is a special mode to use Fibre channel disks. However, in this case all migration hosts must be attached to the same Fibre channel switch. For more information about NPIV, see Section 24.1, “Mapping Physical Storage to Virtual Disks”. Commonly, this works if the Fibre channel environment supports 4 Gbit or faster connections.

26.3.3 Migrating VM Guest Systems

  

The actual migration of the VM Guest system is done with the command: 

> sudo xl migrate <domain_name> <host>

The speed of the migration depends on how fast the memory print can be saved to disk, sent to the new VM Host Server and loaded there. This means that small VM Guest systems can be migrated faster than big systems with a lot of memory.

26.4 Monitoring Xen

  

For a regular operation of many virtual guests, having a possibility to check the sanity of all the different VM Guest systems is indispensable. Xen offers several tools besides the system tools to gather information about the system.

Tip
Tip: Monitoring the VM Host Server

Basic monitoring of the VM Host Server (I/O and CPU) is available via the Virtual Machine Manager. Refer to Section 9.8.1, “Monitoring with Virtual Machine Manager” for details.

26.4.1 Monitor Xen with xentop

  

The preferred terminal application to gather information about Xen virtual environment is xentop. Unfortunately, this tool needs a rather broad terminal, else it inserts line breaks into the display.

xentop has several command keys that can give you more information about the system that is monitored. Some of the more important are:

D

Change the delay between the refreshes of the screen.

N

Also display network statistics. Note, that only standard configurations will be displayed. If you use a special configuration like a routed network, no network will be displayed.

B

Display the respective block devices and their cumulated usage count.

For more information about xentop see the manual page man 1 xentop.

Tip
Tip: virt-top

libvirt offers the hypervisor-agnostic tool virt-top, which is recommended for monitoring VM Guests. See Section 9.8.2, “Monitoring with virt-top” for details.

26.4.2 Additional Tools

  

There are many system tools that also help monitoring or debugging a running SUSE Linux Enterprise system. Many of these are covered in Chapter 2, System Monitoring Utilities. Especially useful for monitoring a virtualization environment are the following tools:

ip

The command line utility ip may be used to monitor arbitrary network interfaces. This is especially useful if you have set up a network that is routed or applied a masqueraded network. To monitor a network interface with the name alice.0, run the following command: 

> watch ip -s link show alice.0
bridge

In a standard setup, all the Xen VM Guest systems are attached to a virtual network bridge. bridge allows you to determine the connection between the bridge and the virtual network adapter in the VM Guest system. For example, the output of bridge link may look like the following: 

2: eth0 state DOWN : <NO-CARRIER, ...,UP> mtu 1500 master br0
8: vnet0 state UNKNOWN : <BROADCAST, ...,LOWER_UP> mtu 1500 master virbr0 \
  state forwarding priority 32 cost 100

This shows that there are two virtual bridges defined on the system. One is connected to the physical Ethernet device eth0, the other one is connected to a VLAN interface vnet0.

iptables-save

Especially when using masquerade networks, or if several Ethernet interfaces are set up together with a firewall setup, it may be helpful to check the current firewall rules.

The command iptables may be used to check all the different firewall settings. To list all the rules of a chain, or even of the complete setup, you may use the commands iptables-save or iptables -S.

26.5 Providing Host Information for VM Guest Systems

  

In a standard Xen environment, the VM Guest systems have only very limited information about the VM Host Server system they are running on. If a guest should know more about the VM Host Server it runs on, vhostmd can provide more information to selected guests. To set up your system to run vhostmd, proceed as follows:

  1. Install the package vhostmd on the VM Host Server.

  2. To add or remove metric sections from the configuration, edit the file /etc/vhostmd/vhostmd.conf. However, the default works well.

  3. Check the validity of the vhostmd.conf configuration file with the command: 

    > cd /etc/vhostmd
> xmllint --postvalid --noout vhostmd.conf

  4. Start the vhostmd daemon with the command sudo systemctl start vhostmd.

    If vhostmd should be started automatically during start-up of the system, run the command: 

    > sudo systemctl enable vhostmd

  5. Attach the image file /dev/shm/vhostmd0 to the VM Guest system named alice with the command: 

    > xl block-attach opensuse /dev/shm/vhostmd0,,xvdb,ro

  6. Log on the VM Guest system.

  7. Install the client package vm-dump-metrics.

  8. Run the command vm-dump-metrics. To save the result to a file, use the option -d <filename>.

The result of the vm-dump-metrics is an XML output. The respective metric entries follow the DTD /etc/vhostmd/metric.dtd.

For more information, see the manual pages man 8 vhostmd and /usr/share/doc/vhostmd/README on the VM Host Server system. On the guest, see the manual page man 1 vm-dump-metrics.