Jump to contentJump to page navigation: previous page [access key p]/next page [access key n]
documentation.suse.com / SUSE Linux Enterprise Server Documentation / Storage Administration Guide / Logical volumes (LVM) / LVM configuration
Applies to SUSE Linux Enterprise Server 15 SP5

5 LVM configuration

This chapter describes the principles behind Logical Volume Manager (LVM) and its basic features that make it useful under many circumstances. The YaST LVM configuration can be reached from the YaST Expert Partitioner. This partitioning tool enables you to edit and delete existing partitions and create new ones that should be used with LVM.

Warning
Warning: Risks

Using LVM might be associated with increased risk, such as data loss. Risks also include application crashes, power failures, and faulty commands. Save your data before implementing LVM or reconfiguring volumes. Never work without a backup.

5.1 Understanding the logical volume manager

LVM enables flexible distribution of hard disk space over several physical volumes (hard disks, partitions, LUNs). It was developed because the need to change the segmentation of hard disk space might arise only after the initial partitioning has already been done during installation. Because it is difficult to modify partitions on a running system, LVM provides a virtual pool (volume group or VG) of storage space from which logical volumes (LVs) can be created as needed. The operating system accesses these LVs instead of the physical partitions. Volume groups can span more than one disk, so that several disks or parts of them can constitute one single VG. In this way, LVM provides a kind of abstraction from the physical disk space that allows its segmentation to be changed in a much easier and safer way than through physical repartitioning.

Figure 5.1, “Physical partitioning versus LVM” compares physical partitioning (left) with LVM segmentation (right). On the left side, one single disk has been divided into three physical partitions (PART), each with a mount point (MP) assigned so that the operating system can access them. On the right side, two disks have been divided into two and three physical partitions each. Two LVM volume groups (VG 1 and VG 2) have been defined. VG 1 contains two partitions from DISK 1 and one from DISK 2. VG 2 contains the remaining two partitions from DISK 2.

Physical partitioning versus LVM
Figure 5.1: Physical partitioning versus LVM

In LVM, the physical disk partitions that are incorporated in a volume group are called physical volumes (PVs). Within the volume groups in Figure 5.1, “Physical partitioning versus LVM”, four logical volumes (LV 1 through LV 4) have been defined, which can be used by the operating system via the associated mount points (MP). The border between different logical volumes need not be aligned with any partition border. See the border between LV 1 and LV 2 in this example.

LVM features:

  • Several hard disks or partitions can be combined in a large logical volume.

  • Provided the configuration is suitable, an LV (such as /usr) can be enlarged when the free space is exhausted.

  • Using LVM, it is possible to add hard disks or LVs in a running system. However, this requires hotpluggable hardware that is capable of such actions.

  • It is possible to activate a striping mode that distributes the data stream of a logical volume over several physical volumes. If these physical volumes reside on different disks, this can improve the reading and writing performance like RAID 0.

  • The snapshot feature enables consistent backups (especially for servers) in the running system.

Note
Note: LVM and RAID

Even though LVM also supports RAID levels 0, 1, 4, 5 and 6, we recommend using mdraid (see Chapter 7, Software RAID configuration). However, LVM works fine with RAID 0 and 1, as RAID 0 is similar to common logical volume management (individual logical blocks are mapped onto blocks on the physical devices). LVM used on top of RAID 1 can keep track of mirror synchronization and is fully able to manage the synchronization process. With higher RAID levels you need a management daemon that monitors the states of attached disks and can inform administrators if there is a problem in the disk array. LVM includes such a daemon, but in exceptional situations such as a device failure, the daemon does not work properly.

Warning
Warning: IBM Z: LVM root file system

If you configure the system with a root file system on LVM or software RAID array, you must place /boot on a separate, non-LVM or non-RAID partition, otherwise the system will fail to boot. The recommended size for such a partition is 500 MB and the recommended file system is Ext4.

With these features, using LVM already makes sense for heavily-used home PCs or small servers. If you have a growing data stock, as in the case of databases, music archives, or user directories, LVM is especially useful. It allows file systems that are larger than the physical hard disk. However, keep in mind that working with LVM is different from working with conventional partitions.

You can manage new or existing LVM storage objects by using the YaST Partitioner. Instructions and further information about configuring LVM are available in the official LVM HOWTO.

5.2 Creating volume groups

An LVM volume group (VG) organizes the Linux LVM partitions into a logical pool of space. You can carve out logical volumes from the available space in the group. The Linux LVM partitions in a group can be on the same or different disks. You can add partitions or entire disks to expand the size of the group.

To use an entire disk, it must not contain any partitions. When using partitions, they must not be mounted. YaST will automatically change their partition type to 0x8E Linux LVM when adding them to a VG.

  1. Launch YaST and open the Partitioner.

  2. In case you need to reconfigure your existing partitioning setup, proceed as follows. Refer to Sección 10.1, “Uso del particionador en modo experto for details. Skip this step if you only want to use unused disks or partitions that already exist.

    Warning
    Warning: Physical volumes on unpartitioned disks

    You can use an unpartitioned disk as a physical volume (PV) if that disk is not the one where the operating system is installed and from which it boots.

    As unpartitioned disks appear as unused at the system level, they can easily be overwritten or wrongly accessed.

    1. To use an entire hard disk that already contains partitions, delete all partitions on that disk.

    2. To use a partition that is currently mounted, unmount it.

  3. In the left panel, select Volume Management.

    A list of existing Volume Groups opens in the right panel.

  4. At the lower left of the Volume Management page, click Add Volume Group.

    Image
  5. Define the volume group as follows:

    1. Specify the Volume Group Name.

      If you are creating a volume group at install time, the name system is suggested for a volume group that will contain the SUSE Linux Enterprise Server system files.

    2. Specify the Physical Extent Size.

      The Physical Extent Size defines the size of a physical block in the volume group. All the disk space in a volume group is handled in chunks of this size. Values can be from 1 KB to 16 GB in powers of 2. This value is normally set to 4 MB.

      In LVM1, a 4 MB physical extent allowed a maximum LV size of 256 GB because it supports only up to 65534 extents per LV. LVM2, which is used on SUSE Linux Enterprise Server, does not restrict the number of physical extents. Having many extents has no impact on I/O performance to the logical volume, but it slows down the LVM tools.

      Important
      Important: Physical extent sizes

      Different physical extent sizes should not be mixed in a single VG. The extent should not be modified after the initial setup.

    3. In the Available Physical Volumes list, select the Linux LVM partitions that you want to make part of this volume group, then click Add to move them to the Selected Physical Volumes list.

    4. Click Finish.

      The new group appears in the Volume Groups list.

  6. On the Volume Management page, click Next, verify that the new volume group is listed, then click Finish.

  7. To check which physical devices are part of the volume group, open the YaST Partitioner at any time in the running system and click Volume Management › Edit › Physical Devices. Leave this screen with Abort.

    Physical volumes in the volume group named DATA
    Figure 5.2: Physical volumes in the volume group named DATA

5.3 Creating logical volumes

A logical volume provides a pool of space similar to what a hard disk does. To make this space usable, you need to define logical volumes. A logical volume is similar to a regular partition—you can format and mount it.

Use the YaST Partitioner to create logical volumes from an existing volume group. Assign at least one logical volume to each volume group. You can create new logical volumes as needed until all free space in the volume group has been exhausted. An LVM logical volume can optionally be thinly provisioned, allowing you to create logical volumes with sizes that overbook the available free space (see Section 5.3.1, “Thinly provisioned logical volumes” for more information).

  • Normal volume: (Default) The volume’s space is allocated immediately.

  • Thin pool: The logical volume is a pool of space that is reserved for use with thin volumes. The thin volumes can allocate their needed space from it on demand.

  • Thin volume: The volume is created as a sparse volume. The volume allocates needed space on demand from a thin pool.

  • Mirrored volume: The volume is created with a defined count of mirrors.

Procedure 5.1: Setting up a logical volume
  1. Launch YaST and open the Partitioner.

  2. In the left panel, select Volume Management. A list of existing Volume Groups opens in the right panel.

  3. Select the volume group in which you want to create the volume and choose Logical Volumes › Add Logical Volume.

  4. Provide a Name for the volume and choose Normal Volume (refer to Section 5.3.1, “Thinly provisioned logical volumes” for setting up thinly provisioned volumes). Proceed with Next.

    Image
  5. Specify the size of the volume and whether to use multiple stripes.

    Using a striped volume, the data will be distributed among several physical volumes. If these physical volumes reside on different hard disks, this generally results in a better reading and writing performance (like RAID 0). The maximum number of available stripes is equal to the number of physical volumes. The default (1 is to not use multiple stripes.

    Image
  6. Choose a Role for the volume. Your choice here only affects the default values for the upcoming dialog. They can be changed in the next step. If in doubt, choose Raw Volume (Unformatted).

    Image
  7. Under Formatting Options, select Format Partition, then select the File system. The content of the Options menu depends on the file system. Usually there is no need to change the defaults.

    Under Mounting Options, select Mount partition, then select the mount point. Click Fstab Options to add special mounting options for the volume.

  8. Click Finish.

  9. Click Next, verify that the changes are listed, then click Finish.

5.3.1 Thinly provisioned logical volumes

An LVM logical volume can optionally be thinly provisioned. Thin provisioning allows you to create logical volumes with sizes that overbook the available free space. You create a thin pool that contains unused space reserved for use with an arbitrary number of thin volumes. A thin volume is created as a sparse volume and space is allocated from a thin pool as needed. The thin pool can be expanded dynamically when needed for cost-effective allocation of storage space. Thinly provisioned volumes also support snapshots which can be managed with Snapper—see Chapter 10, System recovery and snapshot management with Snapper for more information.

To set up a thinly provisioned logical volume, proceed as described in Procedure 5.1, “Setting up a logical volume”. When it comes to choosing the volume type, do not choose Normal Volume, but rather Thin Volume or Thin Pool.

Thin pool

The logical volume is a pool of space that is reserved for use with thin volumes. The thin volumes can allocate their needed space from it on demand.

Thin volume

The volume is created as a sparse volume. The volume allocates needed space on demand from a thin pool.

Important
Important: Thinly provisioned volumes in a cluster

To use thinly provisioned volumes in a cluster, the thin pool and the thin volumes that use it must be managed in a single cluster resource. This allows the thin volumes and thin pool to always be mounted exclusively on the same node.

5.3.2 Creating mirrored volumes

A logical volume can be created with several mirrors. LVM ensures that data written to an underlying physical volume is mirrored onto a different physical volume. Thus even though a physical volume crashes, you can still access the data on the logical volume. LVM also keeps a log file to manage the synchronization process. The log contains information about which volume regions are currently undergoing synchronization with mirrors. By default the log is stored on disk and if possible on a different disk than are the mirrors. But you may specify a different location for the log, for example volatile memory.

Currently there are two types of mirror implementation available: "normal" (non-raid) mirror logical volumes and raid1 logical volumes.

After you create mirrored logical volumes, you can perform standard operations with mirrored logical volumes like activating, extending, and removing.

5.3.2.1 Setting up mirrored non-RAID logical volumes

To create a mirrored volume use the lvcreate command. The following example creates a 500 GB logical volume with two mirrors called lv1, which uses a volume group vg1.

> sudo lvcreate -L 500G -m 2 -n lv1 vg1

Such a logical volume is a linear volume (without striping) that provides three copies of the file system. The m option specifies the count of mirrors. The L option specifies the size of the logical volumes.

The logical volume is divided into regions of the 512 KB default size. If you need a different size of regions, use the -R option followed by the desired region size in megabytes. Or you can configure the preferred region size by editing the mirror_region_size option in the lvm.conf file.

5.3.2.2 Setting up raid1 logical volumes

As LVM supports RAID you can implement mirroring by using RAID1. Such implementation provides the following advantages compared to the non-raid mirrors:

  • LVM maintains a fully redundant bitmap area for each mirror image, which increases its fault handling capabilities.

  • Mirror images can be temporarily split from the array and then merged back.

  • The array can handle transient failures.

  • The LVM RAID 1 implementation supports snapshots.

On the other hand, this type of mirroring implementation does not enable to create a logical volume in a clustered volume group.

To create a mirror volume by using RAID, issue the command

> sudo lvcreate --type raid1 -m 1 -L 1G -n lv1 vg1

where the options/parameters have the following meanings:

  • --type - you need to specify raid1, otherwise the command uses the implicit segment type mirror and creates a non-raid mirror.

  • -m - specifies the count of mirrors.

  • -L - specifies the size of the logical volume.

  • -n - by using this option you specify a name of the logical volume.

  • vg1 - is a name of the volume group used by the logical volume.

LVM creates a logical volume of one extent size for each data volume in the array. If you have two mirrored volumes, LVM creates another two volumes that stores metadata.

After you create a RAID logical volume, you can use the volume in the same way as a common logical volume. You can activate it, extend it, etc.

5.4 Automatically activating non-root LVM volume groups

Activation behavior for non-root LVM volume groups is controlled in the /etc/lvm/lvm.conf file and by the auto_activation_volume_list parameter. By default, the parameter is empty and all volumes are activated. To activate only some volume groups, add the names in quotes and separate them with commas, for example:

auto_activation_volume_list = [ "vg1", "vg2/lvol1", "@tag1", "@*" ]

If you have defined a list in the auto_activation_volume_list parameter, the following will happen:

  1. Each logical volume is first checked against this list.

  2. If it does not match, the logical volume will not be activated.

By default, non-root LVM volume groups are automatically activated on system restart by dracut. This parameter allows you to activate all volume groups on system restart, or to activate only specified non-root LVM volume groups.

5.5 Resizing an existing volume group

The space provided by a volume group can be expanded at any time in the running system without service interruption by adding physical volumes. This will allow you to add logical volumes to the group or to expand the size of existing volumes as described in Section 5.6, “Resizing a logical volume”.

It is also possible to reduce the size of the volume group by removing physical volumes. YaST only allows to remove physical volumes that are currently unused. To find out which physical volumes are currently in use, run the following command. The partitions (physical volumes) listed in the PE Ranges column are the ones in use:

> sudo pvs -o vg_name,lv_name,pv_name,seg_pe_ranges
root's password:
  VG   LV    PV         PE Ranges
             /dev/sda1
  DATA DEVEL /dev/sda5  /dev/sda5:0-3839
  DATA       /dev/sda5
  DATA LOCAL /dev/sda6  /dev/sda6:0-2559
  DATA       /dev/sda7
  DATA       /dev/sdb1
  DATA       /dev/sdc1
  1. Launch YaST and open the Partitioner.

  2. In the left panel, select Volume Management. A list of existing Volume Groups opens in the right panel.

  3. Select the volume group you want to change, activate the Physical Volumes tab, then click Change.

    Image
  4. Do one of the following:

    • Add: Expand the size of the volume group by moving one or more physical volumes (LVM partitions) from the Available Physical Volumes list to the Selected Physical Volumes list.

    • Remove: Reduce the size of the volume group by moving one or more physical volumes (LVM partitions) from the Selected Physical Volumes list to the Available Physical Volumes list.

  5. Click Finish.

  6. Click Next, verify that the changes are listed, then click Finish.

5.6 Resizing a logical volume

In case there is unused free space available in the volume group, you can enlarge a logical volume to provide more usable space. You may also reduce the size of a volume to free space in the volume group that can be used by other logical volumes.

Note
Note: Online resizing

When reducing the size of a volume, YaST automatically resizes its file system, too. Whether a volume that is currently mounted can be resized online (that is while being mounted), depends on its file system. Growing the file system online is supported by Btrfs, XFS, Ext3, and Ext4.

Shrinking the file system online is only supported by Btrfs. To shrink the Ext2/3/4 file systems, you need to unmount them. Shrinking volumes formatted with XFS is not possible, since XFS does not support file system shrinking.

  1. Launch YaST and under System, open the Partitioner.

  2. In the left panel, select the LVM volume group.

  3. Select the logical volume you want to change in the right panel.

  4. Click Device and then Resize.

    Image
  5. Set the intended size by using one of the following options:

    • Maximum size.  Expand the size of the logical volume to use all space left in the volume group.

    • Minimum size.  Reduce the size of the logical volume to the size occupied by the data and the file system metadata.

    • Custom size.  Specify the new size for the volume. The value must be within the range of the minimum and maximum values listed above. Use K, M, G, T for Kilobytes, Megabytes, Gigabytes and Terabytes (for example 20G).

  6. Click Next, verify that the change is listed, then click Finish.

5.7 Deleting a volume group or a logical volume

Warning
Warning: Data loss

Deleting a volume group destroys all of the data in each of its member partitions. Deleting a logical volume destroys all data stored on the volume.

  1. Launch YaST and open the Partitioner.

  2. In the left panel, select Volume Management. A list of existing volume groups opens in the right panel.

  3. Select the volume group or the logical volume you want to remove and click Delete.

  4. Depending on your choice, warning dialogs are shown. Confirm them with Yes.

  5. Click Next, verify that the deleted volume group is listed—deletion is indicated by a red-colored font—then click Finish.

5.8 Disabling LVM on boot

If there is an error on the LVM storage, the scanning of LVM volumes may prevent the emergency/rescue shell from being entered. This makes further problem diagnosis impossible. To disable this scanning in case of an LVM storage failure, you can pass the nolvm option on the kernel command line.

5.9 Using LVM commands

For information about using LVM commands, see the man pages for the commands described in the following table. All commands need to be executed with root privileges. Either use sudo COMMAND (recommended), or execute them directly as root.

LVM commands
pvcreate DEVICE

Initializes a device (such as /dev/sdb1) for use by LVM as a physical volume. If there is any file system on the specified device, a warning appears. Bear in mind that pvcreate checks for existing file systems only if blkid is installed (which is done by default). If blkid is not available, pvcreate will not produce any warning and you may lose your file system without any warning.

pvdisplay DEVICE

Displays information about the LVM physical volume, such as whether it is currently being used in a logical volume.

vgcreate -c y VG_NAME DEV1 [DEV2...]

Creates a clustered volume group with one or more specified devices.

vgcreate --activationmode ACTIVATION_MODE VG_NAME

Configures the mode of volume group activation. You can specify one of the following values:

  • complete - only the logical volumes that are not affected by missing physical volumes can be activated, even though the particular logical volume can tolerate such a failure.

  • degraded - is the default activation mode. If there is a sufficient level of redundancy to activate a logical volume, the logical volume can be activated even though some physical volumes are missing.

  • partial - the LVM tries to activate the volume group even though some physical volumes are missing. If a non-redundant logical volume is missing important physical volumes, then the logical volume usually cannot be activated and is handled as an error target.

vgchange -a [ey|n] VG_NAME

Activates (-a ey) or deactivates (-a n) a volume group and its logical volumes for input/output.

When activating a volume in a cluster, ensure that you use the ey option. This option is used by default in the load script.

vgremove VG_NAME

Removes a volume group. Before using this command, remove the logical volumes, then deactivate the volume group.

vgdisplay VG_NAME

Displays information about a specified volume group.

To find the total physical extent of a volume group, enter

> vgdisplay VG_NAME | grep "Total PE"
lvcreate -L SIZE -n LV_NAME VG_NAME

Creates a logical volume of the specified size.

lvcreate -L SIZE --thinpool POOL_NAME VG_NAME

Creates a thin pool named myPool of the specified size from the volume group VG_NAME.

The following example creates a thin pool with a size of 5 GB from the volume group LOCAL:

> sudo lvcreate -L 5G --thinpool myPool LOCAL
lvcreate -T VG_NAME/POOL_NAME -V SIZE -n LV_NAME

Creates a thin logical volume within the pool POOL_NAME. The following example creates a 1GB thin volume named myThin1 from the pool myPool on the volume group LOCAL:

> sudo lvcreate -T LOCAL/myPool -V 1G -n myThin1
lvcreate -T VG_NAME/POOL_NAME -V SIZE -L SIZE -n LV_NAME

It is also possible to combine thin pool and thin logical volume creation in one command:

> sudo lvcreate -T LOCAL/myPool -V 1G -L 5G -n myThin1
lvcreate --activationmode ACTIVATION_MODE LV_NAME

Configures the mode of logical volume activation. You can specify one of the following values:

  • complete - the logical volume can be activated only if all its physical volumes are active.

  • degraded - is the default activation mode. If there is a sufficient level of redundancy to activate a logical volume, the logical volume can be activated even though some physical volumes are missing.

  • partial - the LVM tries to activate the volume even though some physical volumes are missing. In this case part of the logical volume may be unavailable and it might cause data loss. This option is typically not used, but might be useful when restoring data.

You can specify the activation mode also in /etc/lvm/lvm.conf by specifying one of the above described values of the activation_mode configuration option.

lvcreate -s [-L SIZE] -n SNAP_VOLUME SOURCE_VOLUME_PATH VG_NAME

Creates a snapshot volume for the specified logical volume. If the size option (-L or --size) is not included, the snapshot is created as a thin snapshot.

lvremove /dev/VG_NAME/LV_NAME

Removes a logical volume.

Before using this command, close the logical volume by unmounting it with the umount command.

lvremove SNAP_VOLUME_PATH

Removes a snapshot volume.

lvconvert --merge SNAP_VOLUME_PATH

Reverts the logical volume to the version of the snapshot.

vgextend VG_NAME DEVICE

Adds the specified device (physical volume) to an existing volume group.

vgreduce VG_NAME DEVICE

Removes a specified physical volume from an existing volume group.

Ensure that the physical volume is not currently being used by a logical volume. If it is, you must move the data to another physical volume by using the pvmove command.

lvextend -L SIZE /dev/VG_NAME/LV_NAME

Extends the size of a specified logical volume. Afterward, you must also expand the file system to take advantage of the newly available space. See Chapter 2, Resizing file systems for details.

lvreduce -L SIZE /dev/VG_NAME/LV_NAME

Reduces the size of a specified logical volume.

Ensure that you reduce the size of the file system first before shrinking the volume, otherwise you risk losing data. See Chapter 2, Resizing file systems for details.

lvrename /dev/VG_NAME/LV_NAME /dev/VG_NAME/NEW_LV_NAME

Renames an existing LVM logical volume. It does not change the volume group name.

Tip
Tip: Bypassing udev on volume creation

In case you want to manage LV device nodes and symbolic links by using LVM instead of by using udev rules, you can achieve this by disabling notifications from udev with one of the following methods:

  • Configure activation/udev_rules = 0 and activation/udev_sync = 0 in /etc/lvm/lvm.conf.

    Note that specifying --nodevsync with the lvcreate command has the same effect as activation/udev_sync = 0; setting activation/udev_rules = 0 is still required.

  • Setting the environment variable DM_DISABLE_UDEV:

    export DM_DISABLE_UDEV=1

    This will also disable notifications from udev. In addition, all udev related settings from /etc/lvm/lvm.conf will be ignored.

5.9.1 Resizing a logical volume with commands

The lvresize, lvextend, and lvreduce commands are used to resize logical volumes. See the man pages for each of these commands for syntax and options information. To extend an LV there must be enough unallocated space available on the VG.

The recommended way to grow or shrink a logical volume is to use the YaST Partitioner. When using YaST, the size of the file system in the volume will automatically be adjusted, too.

LVs can be extended or shrunk manually while they are being used, but this may not be true for a file system on them. Extending or shrinking the LV does not automatically modify the size of file systems in the volume. You must use a different command to grow the file system afterward. For information about resizing file systems, see Chapter 2, Resizing file systems.

Ensure that you use the right sequence when manually resizing an LV:

  • If you extend an LV, you must extend the LV before you attempt to grow the file system.

  • If you shrink an LV, you must shrink the file system before you attempt to shrink the LV.

To extend the size of a logical volume:

  1. Open a terminal.

  2. If the logical volume contains an Ext2 or Ext4 file system, which do not support online growing, dismount it. In case it contains file systems that are hosted for a virtual machine (such as a Xen VM), shut down the VM first.

  3. At the terminal prompt, enter the following command to grow the size of the logical volume:

    > sudo lvextend -L +SIZE /dev/VG_NAME/LV_NAME

    For SIZE, specify the amount of space you want to add to the logical volume, such as 10 GB. Replace /dev/VG_NAME/LV_NAME with the Linux path to the logical volume, such as /dev/LOCAL/DATA. For example:

    > sudo lvextend -L +10GB /dev/vg1/v1
  4. Adjust the size of the file system. See Chapter 2, Resizing file systems for details.

  5. In case you have dismounted the file system, mount it again.

For example, to extend an LV with a (mounted and active) Btrfs on it by 10 GB:

> sudo lvextend −L +10G /dev/LOCAL/DATA
> sudo btrfs filesystem resize +10G /dev/LOCAL/DATA

To shrink the size of a logical volume:

  1. Open a terminal.

  2. If the logical volume does not contain a Btrfs file system, dismount it. In case it contains file systems that are hosted for a virtual machine (such as a Xen VM), shut down the VM first. Note that volumes with the XFS file system cannot be reduced in size.

  3. Adjust the size of the file system. See Chapter 2, Resizing file systems for details.

  4. At the terminal prompt, enter the following command to shrink the size of the logical volume to the size of the file system:

    > sudo lvreduce /dev/VG_NAME/LV_NAME
  5. In case you have unmounted the file system, mount it again.

For example, to shrink an LV with a Btrfs on it by 5 GB:

> sudo btrfs filesystem resize -size 5G /dev/LOCAL/DATA
sudo lvreduce /dev/LOCAL/DATA
Tip
Tip: Resizing the Volume and the File System with a Single Command

Starting with SUSE Linux Enterprise Server 12 SP1, lvextend, lvresize, and lvreduce support the option --resizefs which will not only change the size of the volume, but will also resize the file system. Therefore the examples for lvextend and lvreduce shown above can alternatively be run as follows:

> sudo lvextend --resizefs −L +10G /dev/LOCAL/DATA
> sudo lvreduce  --resizefs -L -5G /dev/LOCAL/DATA

Note that the --resizefs is supported for the following file systems: ext2/3/4, Btrfs, XFS. Resizing Btrfs with this option is currently only available on SUSE Linux Enterprise Server, since it is not yet accepted upstream.

5.9.2 Using LVM cache volumes

LVM supports the use of fast block devices (such as an SSD device) as write-back or write-through caches for large slower block devices. The cache logical volume type uses a small and fast LV to improve the performance of a large and slow LV.

To set up LVM caching, you need to create two logical volumes on the caching device. A large one is used for the caching itself, a smaller volume is used to store the caching metadata. These two volumes need to be part of the same volume group as the original volume. When these volumes are created, they need to be converted into a cache pool which needs to be attached to the original volume:

Procedure 5.2: Setting up a cached logical volume
  1. Create the original volume (on a slow device) if not already existing.

  2. Add the physical volume (from a fast device) to the same volume group the original volume is part of and create the cache data volume on the physical volume.

  3. Create the cache metadata volume. The size should be 1/1000 of the size of the cache data volume, with a minimum size of 8 MB.

  4. Combine the cache data volume and metadata volume into a cache pool volume:

    > sudo lvconvert --type cache-pool --poolmetadata VOLUME_GROUP/METADATA_VOLUME VOLUME_GROUP/CACHING_VOLUME
  5. Attach the cache pool to the original volume:

    > sudo lvconvert --type cache --cachepool VOLUME_GROUP/CACHING_VOLUME VOLUME_GROUP/ORIGINAL_VOLUME

For more information on LVM caching, see the lvmcache(7) man page.

5.10 Tagging LVM2 storage objects

A tag is an unordered keyword or term assigned to the metadata of a storage object. Tagging allows you to classify collections of LVM storage objects in ways that you find useful by attaching an unordered list of tags to their metadata.

5.10.1 Using LVM2 tags

After you tag the LVM2 storage objects, you can use the tags in commands to accomplish the following tasks:

  • Select LVM objects for processing according to the presence or absence of specific tags.

  • Use tags in the configuration file to control which volume groups and logical volumes are activated on a server.

  • Override settings in a global configuration file by specifying tags in the command.

A tag can be used in place of any command line LVM object reference that accepts:

  • a list of objects

  • a single object as long as the tag expands to a single object

Replacing the object name with a tag is not supported everywhere yet. After the arguments are expanded, duplicate arguments in a list are resolved by removing the duplicate arguments, and retaining the first instance of each argument.

Wherever there might be ambiguity of argument type, you must prefix a tag with the commercial at sign (@) character, such as @mytag. Elsewhere, using the @ prefix is optional.

5.10.2 Requirements for creating LVM2 tags

Consider the following requirements when using tags with LVM:

Supported characters

An LVM tag word can contain the ASCII uppercase characters A to Z, lowercase characters a to z, numbers 0 to 9, underscore (_), plus (+), hyphen (-), and period (.). The word cannot begin with a hyphen. The maximum length is 128 characters.

Supported storage objects

You can tag LVM2 physical volumes, volume groups, logical volumes, and logical volume segments. PV tags are stored in its volume group’s metadata. Deleting a volume group also deletes the tags in the orphaned physical volume. Snapshots cannot be tagged, but their origin can be tagged.

LVM1 objects cannot be tagged because the disk format does not support it.

5.10.3 Command line tag syntax

--addtagTAG_INFO

Add a tag to (or tag) an LVM2 storage object. Example:

> sudo vgchange --addtag @db1 vg1
--deltagTAG_INFO

Remove a tag from (or untag) an LVM2 storage object. Example:

> sudo vgchange --deltag @db1 vg1
--tagTAG_INFO

Specify the tag to use to narrow the list of volume groups or logical volumes to be activated or deactivated.

Enter the following to activate the volume if it has a tag that matches the tag provided (example):

> sudo lvchange -ay --tag @db1 vg1/vol2

5.10.4 Configuration file syntax

The following sections show example configurations for certain use cases.

5.10.4.1 Enabling host name tags in the lvm.conf file

Add the following code to the /etc/lvm/lvm.conf file to enable host tags that are defined separately on host in a /etc/lvm/lvm_<HOSTNAME>.conf file.

tags {
   # Enable hostname tags
   hosttags = 1
}

You place the activation code in the /etc/lvm/lvm_<HOSTNAME>.conf file on the host. See Section 5.10.4.3, “Defining activation”.

5.10.4.2 Defining tags for host names in the lvm.conf file

tags {

   tag1 { }
      # Tag does not require a match to be set.

   tag2 {
      # If no exact match, tag is not set.
      host_list = [ "hostname1", "hostname2" ]
   }
}

5.10.4.3 Defining activation

You can modify the /etc/lvm/lvm.conf file to activate LVM logical volumes based on tags.

In a text editor, add the following code to the file:

  activation {
      volume_list = [ "vg1/lvol0", "@database" ]
  }

Replace @database with your tag. Use "@*" to match the tag against any tag set on the host.

The activation command matches against VGNAME, VGNAME/LVNAME, or @TAG set in the metadata of volume groups and logical volumes. A volume group or logical volume is activated only if a metadata tag matches. The default if there is no match, is not to activate.

If volume_list is not present and tags are defined on the host, then it activates the volume group or logical volumes only if a host tag matches a metadata tag.

If volume_list is defined, but empty, and no tags are defined on the host, then it does not activate.

If volume_list is undefined, it imposes no limits on LV activation (all are allowed).

5.10.4.4 Defining activation in multiple host name configuration files

You can use the activation code in a host’s configuration file (/etc/lvm/lvm_<HOST_TAG>.conf) when host tags are enabled in the lvm.conf file. For example, a server has two configuration files in the /etc/lvm/ directory:

lvm.conf
lvm_<HOST_TAG>.conf

At start-up, load the /etc/lvm/lvm.conf file, and process any tag settings in the file. If any host tags were defined, it loads the related /etc/lvm/lvm_<HOST_TAG>.conf file. When it searches for a specific configuration file entry, it searches the host tag file first, then the lvm.conf file, and stops at the first match. Within the lvm_<HOST_TAG>.conf file, use the reverse order that tags were set in. This allows the file for the last tag set to be searched first. New tags set in the host tag file will trigger additional configuration file loads.

5.10.5 Using tags for a simple activation control in a cluster

You can set up a simple host name activation control by enabling the hostname_tags option in the /etc/lvm/lvm.conf file. Use the same file on every machine in a cluster so that it is a global setting.

  1. In a text editor, add the following code to the /etc/lvm/lvm.conf file:

    tags {
       hostname_tags = 1
    }
  2. Replicate the file to all hosts in the cluster.

  3. From any machine in the cluster, add db1 to the list of machines that activate vg1/lvol2:

    > sudo lvchange --addtag @db1 vg1/lvol2
  4. On the db1 server, enter the following to activate it:

    > sudo lvchange -ay vg1/vol2

5.10.6 Using tags to activate on preferred hosts in a cluster

The examples in this section demonstrate two methods to accomplish the following:

  • Activate volume group vg1 only on the database hosts db1 and db2.

  • Activate volume group vg2 only on the file server host fs1.

  • Activate nothing initially on the file server backup host fsb1, but be prepared for it to take over from the file server host fs1.

5.10.6.1 Option 1: centralized admin and static configuration replicated between hosts

In the following solution, the single configuration file is replicated among multiple hosts.

  1. Add the @database tag to the metadata of volume group vg1. In a terminal, enter

    > sudo vgchange --addtag @database vg1
  2. Add the @fileserver tag to the metadata of volume group vg2. In a terminal, enter

    > sudo vgchange --addtag @fileserver vg2
  3. In a text editor, modify the /etc/lvm/lvm.conf file with the following code to define the @database, @fileserver, @fileserverbackup tags.

    tags {
       database {
          host_list = [ "db1", "db2" ]
       }
       fileserver {
          host_list = [ "fs1" ]
       }
       fileserverbackup {
          host_list = [ "fsb1" ]
       }
    }
    
    activation {
       # Activate only if host has a tag that matches a metadata tag
       volume_list = [ "@*" ]
    }
  4. Replicate the modified /etc/lvm/lvm.conf file to the four hosts: db1, db2, fs1, and fsb1.

  5. If the file server host goes down, vg2 can be brought up on fsb1 by entering the following commands in a terminal on any node:

    > sudo vgchange --addtag @fileserverbackup vg2
    > sudo vgchange -ay vg2

5.10.6.2 Option 2: localized admin and configuration

In the following solution, each host holds locally the information about which classes of volume to activate.

  1. Add the @database tag to the metadata of volume group vg1. In a terminal, enter

    > sudo vgchange --addtag @database vg1
  2. Add the @fileserver tag to the metadata of volume group vg2. In a terminal, enter

    > sudo vgchange --addtag @fileserver vg2
  3. Enable host tags in the /etc/lvm/lvm.conf file:

    1. In a text editor, modify the /etc/lvm/lvm.conf file with the following code to enable host tag configuration files.

      tags {
         hosttags = 1
      }
    2. Replicate the modified /etc/lvm/lvm.conf file to the four hosts: db1, db2, fs1, and fsb1.

  4. On host db1, create an activation configuration file for the database host db1. In a text editor, create /etc/lvm/lvm_db1.conf file and add the following code:

    activation {
       volume_list = [ "@database" ]
    }
  5. On host db2, create an activation configuration file for the database host db2. In a text editor, create /etc/lvm/lvm_db2.conf file and add the following code:

    activation {
       volume_list = [ "@database" ]
    }
  6. On host fs1, create an activation configuration file for the file server host fs1. In a text editor, create /etc/lvm/lvm_fs1.conf file and add the following code:

    activation {
       volume_list = [ "@fileserver" ]
    }
  7. If the file server host fs1 goes down, to bring up a spare file server host fsb1 as a file server:

    1. On host fsb1, create an activation configuration file for the host fsb1. In a text editor, create /etc/lvm/lvm_fsb1.conf file and add the following code:

      activation {
         volume_list = [ "@fileserver" ]
      }
    2. In a terminal, enter one of the following commands:

      > sudo vgchange -ay vg2
      > sudo vgchange -ay @fileserver