2 System monitoring utilities #
There are number of programs, tools, and utilities which you can use to examine the status of your system. This chapter introduces some and describes their most important and frequently used parameters.
supportconfig
Apart from the utilities presented in the following, SUSE Linux Enterprise Server
also contains supportconfig
, a tool to create reports
about the system such as: current kernel version, hardware, installed
packages, partition setup and much more. These reports are used to
provide the SUSE support with needed information in case a support
ticket is created. However, they can also be analyzed for known issues to
help resolve problems faster. For this purpose, SUSE Linux Enterprise Server provides
both an appliance and a command line tool for Supportconfig Analysis
(SCA). See Chapter 47, Gathering system information for support for details.
For each of the described commands, examples of the relevant outputs are
presented. In the examples, the first line is the command itself (after
the tux
> or root #). Omissions are indicated with
square brackets ([...]
) and long lines are wrapped
where necessary. Line breaks for long lines are indicated by a backslash
(\
).
>
command -x -y
output line 1
output line 2
output line 3 is annoyingly long, so long that \
we need to break it
output line 4
[...]
output line 98
output line 99
The descriptions have been kept short so that we can include as many
utilities as possible. Further information for all the commands can be
found in the manual pages. Most of the commands also understand the
parameter --help
, which produces a brief list of possible
parameters.
2.1 Multi-purpose tools #
While most Linux system monitoring tools monitor only a single aspect of the system, there are a few tools with a broader scope. To get an overview and find out which part of the system to examine further, use these tools first.
2.1.1 vmstat
#
vmstat collects information about processes, memory, I/O, interrupts and CPU:
vmstat [options] [delay [count]]
When called without values for delay and count, it displays average values since the last reboot. When called with a value for delay (in seconds), it displays values for the given period (two seconds in the examples below). The value for count specifies the number of updates vmstat should perform. If not specified, it will run until manually stopped.
vmstat
output on a lightly used machine #>
vmstat 2
procs -----------memory---------- ---swap-- -----io---- -system-- ------cpu-----
r b swpd free buff cache si so bi bo in cs us sy id wa st
1 0 44264 81520 424 935736 0 0 12 25 27 34 1 0 98 0 0
0 0 44264 81552 424 935736 0 0 0 0 38 25 0 0 100 0 0
0 0 44264 81520 424 935732 0 0 0 0 23 15 0 0 100 0 0
0 0 44264 81520 424 935732 0 0 0 0 36 24 0 0 100 0 0
0 0 44264 81552 424 935732 0 0 0 0 51 38 0 0 100 0 0
vmstat
output on a heavily used machine (CPU bound) #>
vmstat 2
procs -----------memory----------- ---swap-- -----io---- -system-- -----cpu------
r b swpd free buff cache si so bi bo in cs us sy id wa st
32 1 26236 459640 110240 6312648 0 0 9944 2 4552 6597 95 5 0 0 0
23 1 26236 396728 110336 6136224 0 0 9588 0 4468 6273 94 6 0 0 0
35 0 26236 554920 110508 6166508 0 0 7684 27992 4474 4700 95 5 0 0 0
28 0 26236 518184 110516 6039996 0 0 10830 4 4446 4670 94 6 0 0 0
21 5 26236 716468 110684 6074872 0 0 8734 20534 4512 4061 96 4 0 0 0
The first line of the vmstat output always displays average values since the last reboot.
The columns show the following:
Shows the number of processes in a runnable state. These processes are either executing or waiting for a free CPU slot. If the number of processes in this column is constantly higher than the number of CPUs available, this may be an indication of insufficient CPU power.
Shows the number of processes waiting for a resource other than a CPU. A high number in this column may indicate an I/O problem (network or disk).
The amount of swap space (KB) currently used.
The amount of unused memory (KB).
Recently unused memory that can be reclaimed. This column is only visible when calling
vmstat
with the parameter-a
(recommended).Recently used memory that normally does not get reclaimed. This column is only visible when calling
vmstat
with the parameter-a
(recommended).File buffer cache (KB) in RAM that contains file system metadata. This column is not visible when calling
vmstat
with the parameter-a
.Page cache (KB) in RAM with the actual contents of files. This column is not visible when calling
vmstat
with the parameter-a
.Amount of data (KB) that is moved from swap to RAM (
si
) or from RAM to swap (so
) per second. Highso
values over a long period of time may indicate that an application is leaking memory and the leaked memory is being swapped out. Highsi
values over a long period of time could mean that an application that was inactive for a very long time is now active again. Combined highsi
andso
values for prolonged periods of time are evidence of swap thrashing and may indicate that more RAM needs to be installed in the system because there is not enough memory to hold the working set size.Number of blocks per second received from a block device (for example, a disk read). Note that swapping also impacts the values shown here. The block size may vary between file systems but can be determined using the stat utility. If throughput data is required then iostat may be used.
Number of blocks per second sent to a block device (for example, a disk write). Note that swapping also impacts the values shown here.
Interrupts per second. A high value may indicate a high I/O level (network and/or disk), but could also be triggered for other reasons such as inter-processor interrupts triggered by another activity. Make sure to also check
/proc/interrupts
to identify the source of interrupts.Number of context switches per second. This is the number of times that the kernel replaces executable code of one program in memory with that of another program.
Percentage of CPU usage executing application code.
Percentage of CPU usage executing kernel code.
Percentage of CPU time spent idling. If this value is zero over a longer time, your CPU(s) are working to full capacity. This is not necessarily a bad sign—rather refer to the values in columns
and to determine if your machine is equipped with sufficient CPU power.If "wa" time is non-zero, it indicates throughput lost because of waiting for I/O. This may be inevitable, for example, if a file is being read for the first time, background writeback cannot keep up, and so on. It can also be an indicator for a hardware bottleneck (network or hard disk). Lastly, it can indicate a potential for tuning the virtual memory manager (refer to Chapter 16, Tuning the memory management subsystem).
Percentage of CPU time stolen from a virtual machine.
See vmstat
--help
for more options.
2.1.2 dstat
#
dstat
is a replacement for tools such as
vmstat
, iostat
,
netstat
, or ifstat
.
dstat
displays information about the system
resources in real time. For example, you can compare disk usage
in combination with interrupts from the IDE controller, or compare
network bandwidth with the disk throughput (in the same interval).
By default, its output is presented in readable tables. Alternatively, CSV output can be produced which is suitable as a spreadsheet import format.
It is written in Python and can be enhanced with plug-ins.
This is the general syntax:
dstat [-afv] [OPTIONS..] [DELAY [COUNT]]
All options and parameters are optional. Without any parameter, dstat
displays statistics about CPU (-c
,
--cpu
), disk (-d
,
--disk
), network (-n
,
--net
), paging (-g
,
--page
), and the interrupts and context switches of
the system (-y
, --sys
); it refreshes
the output every second ad infinitum:
#
dstat
You did not select any stats, using -cdngy by default. ----total-cpu-usage---- -dsk/total- -net/total- ---paging-- ---system-- usr sys idl wai hiq siq| read writ| recv send| in out | int csw 0 0 100 0 0 0| 15k 44k| 0 0 | 0 82B| 148 194 0 0 100 0 0 0| 0 0 |5430B 170B| 0 0 | 163 187 0 0 100 0 0 0| 0 0 |6363B 842B| 0 0 | 196 185
-a
,--all
equal to
-cdngy
(default)-f
,--full
expand
-C
,-D
,-I
,-N
and-S
discovery lists-v
,--vmstat
equal to
-pmgdsc
,-D total
- DELAY
delay in seconds between each update
- COUNT
the number of updates to display before exiting
The default delay is 1 and the count is unspecified (unlimited).
For more information, see the man page of dstat
and
its Web page at http://dag.wieers.com/home-made/dstat/.
2.1.3 System activity information: sar
#
sar
can generate extensive reports on almost all
important system activities, among them CPU, memory, IRQ usage, I/O, and
networking. It can also generate reports in real time.
The sar
command gathers data from the
/proc
file system.
The sar
command is a part of the
sysstat package. Install it with YaST, or with
the zypper in sysstat
command. sysstat.service
does not start by default,
and must be enabled and started with the following command:
>
sudo
systemctl enable --now sysstat
2.1.3.1 Generating reports with sar
#
To generate reports in real time, call sar
with an
interval (seconds) and a count. To generate reports from files specify
a file name with the option -f
instead of interval and
count. If file name, interval and count are not specified,
sar
attempts to generate a report from
/var/log/sa/saDD
, where
DD stands for the current day. This is the
default location to where sadc
(the system
activity data collector) writes its data.
Query multiple files with multiple -f options.
sar 2 10 # real time report, 10 times every 2 seconds sar -f ~/reports/sar_2014_07_17 # queries file sar_2014_07_17 sar # queries file from today in /var/log/sa/ cd /var/log/sa && \ sar -f sa01 -f sa02 # queries files /var/log/sa/0[12]
Find examples for useful sar
calls and their
interpretation below. For detailed information on the meaning of each
column, refer to the man (1)
of
sar
.
When the sysstat
service is stopped (for example, during
reboot or shutdown), the tool still collects last-minute statistics by
automatically running the /usr/lib64/sa/sa1 -S ALL 1 1
command. The collected binary data is stored in the system activity data
file.
2.1.3.1.1 CPU usage report: sar
#
When called with no options, sar
shows a basic
report about CPU usage. On multi-processor machines, results for all
CPUs are summarized. Use the option -P ALL
to also
see statistics for individual CPUs.
#
sar 10 5
Linux 4.4.21-64-default (jupiter) 10/12/16 _x86_64_ (2 CPU)
17:51:29 CPU %user %nice %system %iowait %steal %idle
17:51:39 all 57,93 0,00 9,58 1,01 0,00 31,47
17:51:49 all 32,71 0,00 3,79 0,05 0,00 63,45
17:51:59 all 47,23 0,00 3,66 0,00 0,00 49,11
17:52:09 all 53,33 0,00 4,88 0,05 0,00 41,74
17:52:19 all 56,98 0,00 5,65 0,10 0,00 37,27
Average: all 49,62 0,00 5,51 0,24 0,00 44,62
displays the percentage of time that the CPU was idle while waiting for an I/O request. If this value is significantly higher than zero over a longer time, there is a bottleneck in the I/O system (network or hard disk). If the value is zero over a longer time, your CPU is working at capacity.
2.1.3.1.2 Memory usage report: sar
-r
#
Generate an overall picture of the system memory (RAM) by using the
option -r
:
#
sar -r 10 5
Linux 4.4.21-64-default (jupiter) 10/12/16 _x86_64_ (2 CPU)
17:55:27 kbmemfree kbmemused %memused kbbuffers kbcached kbcommit %commit kbactive kbinact kbdirty
17:55:37 104232 1834624 94.62 20 627340 2677656 66.24 802052 828024 1744
17:55:47 98584 1840272 94.92 20 624536 2693936 66.65 808872 826932 2012
17:55:57 87088 1851768 95.51 20 605288 2706392 66.95 827260 821304 1588
17:56:07 86268 1852588 95.55 20 599240 2739224 67.77 829764 820888 3036
17:56:17 104260 1834596 94.62 20 599864 2730688 67.56 811284 821584 3164
Average: 96086 1842770 95.04 20 611254 2709579 67.03 815846 823746 2309
The columns
and show an approximation of the maximum amount of memory (RAM and swap) that the current workload could need. While displays the absolute number in kilobytes, displays a percentage.2.1.3.1.3 Paging statistics report: sar
-B
#
Use the option -B
to display the kernel paging
statistics.
#
sar -B 10 5
Linux 4.4.21-64-default (jupiter) 10/12/16 _x86_64_ (2 CPU)
18:23:01 pgpgin/s pgpgout/s fault/s majflt/s pgfree/s pgscank/s pgscand/s pgsteal/s %vmeff
18:23:11 366.80 11.60 542.50 1.10 4354.80 0.00 0.00 0.00 0.00
18:23:21 0.00 333.30 1522.40 0.00 18132.40 0.00 0.00 0.00 0.00
18:23:31 47.20 127.40 1048.30 0.10 11887.30 0.00 0.00 0.00 0.00
18:23:41 46.40 2.50 336.10 0.10 7945.00 0.00 0.00 0.00 0.00
18:23:51 0.00 583.70 2037.20 0.00 17731.90 0.00 0.00 0.00 0.00
Average: 92.08 211.70 1097.30 0.26 12010.28 0.00 0.00 0.00 0.00
The
(major faults per second) column shows how many pages are loaded from disk into memory. The source of the faults may be file accesses or faults. At times, many major faults are normal. For example, during application start-up time. If major faults are experienced for the entire lifetime of the application it may be an indication that there is insufficient main memory, particularly if combined with large amounts of direct scanning (pgscand/s).The
column shows the number of pages scanned ( ) in relation to the ones being reused from the main memory cache or the swap cache ( ). It is a measurement of the efficiency of page reclaim. Healthy values are either near 100 (every inactive page swapped out is being reused) or 0 (no pages have been scanned). The value should not drop below 30.2.1.3.1.4 Block device statistics report: sar
-d
#
Use the option -d
to display the block device (hard
disk, optical drive, USB storage device, etc.). Make sure to use the
additional option -p
(pretty-print) to make the
column readable.
#
sar -d -p 10 5
Linux 4.4.21-64-default (jupiter) 10/12/16 _x86_64_ (2 CPU)
18:46:09 DEV tps rd_sec/s wr_sec/s avgrq-sz avgqu-sz await svctm %util
18:46:19 sda 1.70 33.60 0.00 19.76 0.00 0.47 0.47 0.08
18:46:19 sr0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
18:46:19 DEV tps rd_sec/s wr_sec/s avgrq-sz avgqu-sz await svctm %util
18:46:29 sda 8.60 114.40 518.10 73.55 0.06 7.12 0.93 0.80
18:46:29 sr0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
18:46:29 DEV tps rd_sec/s wr_sec/s avgrq-sz avgqu-sz await svctm %util
18:46:39 sda 40.50 3800.80 454.90 105.08 0.36 8.86 0.69 2.80
18:46:39 sr0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
18:46:39 DEV tps rd_sec/s wr_sec/s avgrq-sz avgqu-sz await svctm %util
18:46:49 sda 1.40 0.00 204.90 146.36 0.00 0.29 0.29 0.04
18:46:49 sr0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
18:46:49 DEV tps rd_sec/s wr_sec/s avgrq-sz avgqu-sz await svctm %util
18:46:59 sda 3.30 0.00 503.80 152.67 0.03 8.12 1.70 0.56
18:46:59 sr0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
Average: DEV tps rd_sec/s wr_sec/s avgrq-sz avgqu-sz await svctm %util
Average: sda 11.10 789.76 336.34 101.45 0.09 8.07 0.77 0.86
Average: sr0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
Compare the
values for , , and of all disks. Constantly high values in the and columns could be an indication that I/O subsystem is a bottleneck.If the machine uses multiple disks, then it is best if I/O is interleaved evenly between disks of equal speed and capacity. It will be necessary to take into account whether the storage has multiple tiers. Furthermore, if there are multiple paths to storage then consider what the link saturation will be when balancing how storage is used.
2.1.3.1.5 Network statistics reports: sar
-n KEYWORD
#
The option -n
lets you generate multiple network
related reports. Specify one of the following keywords along with the
-n
:
DEV: Generates a statistic report for all network devices
EDEV: Generates an error statistics report for all network devices
NFS: Generates a statistic report for an NFS client
NFSD: Generates a statistic report for an NFS server
SOCK: Generates a statistic report on sockets
ALL: Generates all network statistic reports
2.1.3.2 Visualizing sar
data #
sar
reports are not always easy to parse for humans.
kSar, a Java application visualizing your sar
data,
creates easy-to-read graphs. It can even generate PDF reports. kSar
takes data generated in real time, and past data from a file. kSar
is licensed under the BSD license and is available from
https://sourceforge.net/projects/ksar/.
2.2 System information #
2.2.1 Device load information: iostat
#
To monitor the system device load, use iostat
. It
generates reports that can be useful for better balancing the load
between physical disks attached to your system.
To be able to use iostat
, install the package
sysstat.
The first iostat
report shows statistics collected
since the system was booted. Subsequent reports cover the time since the
previous report.
>
iostat
Linux 4.4.21-64-default (jupiter) 10/12/16 _x86_64_ (4 CPU)
avg-cpu: %user %nice %system %iowait %steal %idle
17.68 4.49 4.24 0.29 0.00 73.31
Device: tps kB_read/s kB_wrtn/s kB_read kB_wrtn
sdb 2.02 36.74 45.73 3544894 4412392
sda 1.05 5.12 13.47 493753 1300276
sdc 0.02 0.14 0.00 13641 37
Invoking iostat
in this way will help you find out
whether throughput is different from your expectation, but not why.
Such questions can be better answered by an extended report which can be
generated by invoking iostat
-x
.
Extended reports additionally include, for example, information on average
queue sizes and average wait times.
It may also be easier to evaluate the data if idle block devices are
excluded using the -z
switch.
Find definitions for each of the displayed column titles in the
man page of iostat
(man 1 iostat
).
You can also specify that a certain device should be monitored at specified
intervals.
For example, to generate five reports at three-second intervals for the
device sda
, use:
>
iostat
-p sda 3 5
To show statistics of network file systems (NFS), there are two similar utilities:
nfsiostat-sysstat
is included with the package sysstat.nfsiostat
is included with the package nfs-client.
iostat
in multipath setups
The iostat
command might not show all controllers
that are listed by nvme list-subsys
. By default,
iostat
filters out all block devices with no I/O.
To make iostat
show all
devices, use the following command:
>
iostat -p ALL
2.2.2 Processor activity monitoring: mpstat
#
The utility mpstat
examines activities of each
available processor. If your system has one processor only, the global
average statistics will be reported.
The timing arguments work the same way as with the
iostat
command. Entering mpstat 2
5
prints five reports for all processors in two-second
intervals.
#
mpstat 2 5
Linux 4.4.21-64-default (jupiter) 10/12/16 _x86_64_ (2 CPU)
13:51:10 CPU %usr %nice %sys %iowait %irq %soft %steal %guest %gnice %idle
13:51:12 all 8,27 0,00 0,50 0,00 0,00 0,00 0,00 0,00 0,00 91,23
13:51:14 all 46,62 0,00 3,01 0,00 0,00 0,25 0,00 0,00 0,00 50,13
13:51:16 all 54,71 0,00 3,82 0,00 0,00 0,51 0,00 0,00 0,00 40,97
13:51:18 all 78,77 0,00 5,12 0,00 0,00 0,77 0,00 0,00 0,00 15,35
13:51:20 all 51,65 0,00 4,30 0,00 0,00 0,51 0,00 0,00 0,00 43,54
Average: all 47,85 0,00 3,34 0,00 0,00 0,40 0,00 0,00 0,00 48,41
From the mpstat
data, you can see:
The ratio between the
and . For example, a ratio of 10:1 indicates the workload is mostly running application code and analysis should focus on the application. A ratio of 1:10 indicates the workload is mostly kernel-bound and tuning the kernel is worth considering. Alternatively, determine why the application is kernel-bound and see if that can be alleviated.Whether there is a subset of CPUs that are nearly fully utilized even if the system is lightly loaded overall. Few hot CPUs can indicate that the workload is not parallelized and could benefit from executing on a machine with a smaller number of faster processors.
2.2.3 Processor frequency monitoring: turbostat
#
turbostat
shows frequencies, load, temperature, and power
of AMD64/Intel 64 processors. It can operate in two modes: If called
with a command, the command process is forked and statistics are displayed
upon command completion. When run without a command, it will display
updated statistics every five seconds. Note that
turbostat
requires the kernel module
msr
to be loaded.
>
sudo
turbostat find /etc -type d -exec true {} \; 0.546880 sec CPU Avg_MHz Busy% Bzy_MHz TSC_MHz - 416 28.43 1465 3215 0 631 37.29 1691 3215 1 416 27.14 1534 3215 2 270 24.30 1113 3215 3 406 26.57 1530 3214 4 505 32.46 1556 3214 5 270 22.79 1184 3214
The output depends on the CPU type and may vary. To display more details
such as temperature and power, use the --debug
option. For
more command line options and an explanation of the field descriptions,
refer to man 8 turbostat
.
2.2.4 Task monitoring: pidstat
#
If you need to see what load a particular task applies to your system,
use pidstat
command. It prints activity of every
selected task or all tasks managed by Linux kernel if no task is
specified. You can also set the number of reports to be displayed and
the time interval between them.
For example, pidstat
-C
firefox 2 3
prints the load statistic for tasks whose command name includes the
string “firefox”. There will be three reports printed at
two second intervals.
#
pidstat -C firefox 2 3
Linux 4.4.21-64-default (jupiter) 10/12/16 _x86_64_ (2 CPU)
14:09:11 UID PID %usr %system %guest %CPU CPU Command
14:09:13 1000 387 22,77 0,99 0,00 23,76 1 firefox
14:09:13 UID PID %usr %system %guest %CPU CPU Command
14:09:15 1000 387 46,50 3,00 0,00 49,50 1 firefox
14:09:15 UID PID %usr %system %guest %CPU CPU Command
14:09:17 1000 387 60,50 7,00 0,00 67,50 1 firefox
Average: UID PID %usr %system %guest %CPU CPU Command
Average: 1000 387 43,19 3,65 0,00 46,84 - firefox
Similarly, pidstat
-d
can be
used to estimate how much I/O tasks are doing, whether they are
sleeping on that I/O and how many clock ticks the task was stalled.
2.2.5 Kernel ring buffer: dmesg
#
The Linux kernel keeps certain messages in a ring buffer. To view these
messages, enter the command dmesg -T
.
Older events are logged in the systemd
journal. See
Chapter 21, journalctl
: query the systemd
journal for more information on the journal.
2.2.6 List of open files: lsof
#
To view a list of all the files open for the process with process ID
PID, use -p
. For example, to
view all the files used by the current shell, enter:
#
lsof -p $$
COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME
bash 8842 root cwd DIR 0,32 222 6772 /root
bash 8842 root rtd DIR 0,32 166 256 /
bash 8842 root txt REG 0,32 656584 31066 /bin/bash
bash 8842 root mem REG 0,32 1978832 22993 /lib64/libc-2.19.so
[...]
bash 8842 root 2u CHR 136,2 0t0 5 /dev/pts/2
bash 8842 root 255u CHR 136,2 0t0 5 /dev/pts/2
The special shell variable $$
, whose value is the
process ID of the shell, has been used.
When used with -i
, lsof
lists
currently open Internet files as well:
#
lsof -i
COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME
wickedd-d 917 root 8u IPv4 16627 0t0 UDP *:bootpc
wickedd-d 918 root 8u IPv6 20752 0t0 UDP [fe80::5054:ff:fe72:5ead]:dhcpv6-client
sshd 3152 root 3u IPv4 18618 0t0 TCP *:ssh (LISTEN)
sshd 3152 root 4u IPv6 18620 0t0 TCP *:ssh (LISTEN)
master 4746 root 13u IPv4 20588 0t0 TCP localhost:smtp (LISTEN)
master 4746 root 14u IPv6 20589 0t0 TCP localhost:smtp (LISTEN)
sshd 8837 root 5u IPv4 293709 0t0 TCP jupiter.suse.de:ssh->venus.suse.de:33619 (ESTABLISHED)
sshd 8837 root 9u IPv6 294830 0t0 TCP localhost:x11 (LISTEN)
sshd 8837 root 10u IPv4 294831 0t0 TCP localhost:x11 (LISTEN)
2.2.7 Kernel and udev event sequence viewer: udevadm monitor
#
udevadm monitor
listens to the kernel uevents and
events sent out by a udev rule and prints the device path (DEVPATH) of
the event to the console. This is a sequence of events while connecting
a USB memory stick:
Only root user is allowed to monitor udev events by running the
udevadm
command.
UEVENT[1138806687] add@/devices/pci0000:00/0000:00:1d.7/usb4/4-2/4-2.2 UEVENT[1138806687] add@/devices/pci0000:00/0000:00:1d.7/usb4/4-2/4-2.2/4-2.2 UEVENT[1138806687] add@/class/scsi_host/host4 UEVENT[1138806687] add@/class/usb_device/usbdev4.10 UDEV [1138806687] add@/devices/pci0000:00/0000:00:1d.7/usb4/4-2/4-2.2 UDEV [1138806687] add@/devices/pci0000:00/0000:00:1d.7/usb4/4-2/4-2.2/4-2.2 UDEV [1138806687] add@/class/scsi_host/host4 UDEV [1138806687] add@/class/usb_device/usbdev4.10 UEVENT[1138806692] add@/devices/pci0000:00/0000:00:1d.7/usb4/4-2/4-2.2/4-2.2 UEVENT[1138806692] add@/block/sdb UEVENT[1138806692] add@/class/scsi_generic/sg1 UEVENT[1138806692] add@/class/scsi_device/4:0:0:0 UDEV [1138806693] add@/devices/pci0000:00/0000:00:1d.7/usb4/4-2/4-2.2/4-2.2 UDEV [1138806693] add@/class/scsi_generic/sg1 UDEV [1138806693] add@/class/scsi_device/4:0:0:0 UDEV [1138806693] add@/block/sdb UEVENT[1138806694] add@/block/sdb/sdb1 UDEV [1138806694] add@/block/sdb/sdb1 UEVENT[1138806694] mount@/block/sdb/sdb1 UEVENT[1138806697] umount@/block/sdb/sdb1
2.3 Processes #
2.3.1 Interprocess communication: ipcs
#
The command ipcs
produces a list of the IPC resources
currently in use:
#
ipcs
------ Message Queues --------
key msqid owner perms used-bytes messages
------ Shared Memory Segments --------
key shmid owner perms bytes nattch status
0x00000000 65536 tux 600 524288 2 dest
0x00000000 98305 tux 600 4194304 2 dest
0x00000000 884738 root 600 524288 2 dest
0x00000000 786435 tux 600 4194304 2 dest
0x00000000 12058628 tux 600 524288 2 dest
0x00000000 917509 root 600 524288 2 dest
0x00000000 12353542 tux 600 196608 2 dest
0x00000000 12451847 tux 600 524288 2 dest
0x00000000 11567114 root 600 262144 1 dest
0x00000000 10911763 tux 600 2097152 2 dest
0x00000000 11665429 root 600 2336768 2 dest
0x00000000 11698198 root 600 196608 2 dest
0x00000000 11730967 root 600 524288 2 dest
------ Semaphore Arrays --------
key semid owner perms nsems
0xa12e0919 32768 tux 666 2
2.3.2 Process list: ps
#
The command ps
produces a list of processes. Most
parameters must be written without a minus sign. Refer to ps
--help
for a brief help or to the man page for extensive help.
To list all processes with user and command line information, use
ps axu
:
>
ps axu
USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND
root 1 0.0 0.3 34376 4608 ? Ss Jul24 0:02 /usr/lib/systemd/systemd
root 2 0.0 0.0 0 0 ? S Jul24 0:00 [kthreadd]
root 3 0.0 0.0 0 0 ? S Jul24 0:00 [ksoftirqd/0]
root 5 0.0 0.0 0 0 ? S< Jul24 0:00 [kworker/0:0H]
root 6 0.0 0.0 0 0 ? S Jul24 0:00 [kworker/u2:0]
root 7 0.0 0.0 0 0 ? S Jul24 0:00 [migration/0]
[...]
tux 12583 0.0 0.1 185980 2720 ? Sl 10:12 0:00 /usr/lib/gvfs/gvfs-mtp-volume-monitor
tux 12587 0.0 0.1 198132 3044 ? Sl 10:12 0:00 /usr/lib/gvfs/gvfs-gphoto2-volume-monitor
tux 12591 0.0 0.1 181940 2700 ? Sl 10:12 0:00 /usr/lib/gvfs/gvfs-goa-volume-monitor
tux 12594 8.1 10.6 1418216 163564 ? Sl 10:12 0:03 /usr/bin/gnome-shell
tux 12600 0.0 0.3 393448 5972 ? Sl 10:12 0:00 /usr/lib/gnome-settings-daemon-3.0/gsd-printer
tux 12625 0.0 0.6 227776 10112 ? Sl 10:12 0:00 /usr/lib/gnome-control-center-search-provider
tux 12626 0.5 1.5 890972 23540 ? Sl 10:12 0:00 /usr/bin/nautilus --no-default-window
[...]
To check how many sshd
processes are running, use the
option -p
together with the command
pidof
, which lists the process IDs of the given
processes.
>
ps -p $(pidof sshd)
PID TTY STAT TIME COMMAND
1545 ? Ss 0:00 /usr/sbin/sshd -D
4608 ? Ss 0:00 sshd: root@pts/0
The process list can be formatted according to your needs. The option
L
returns a list of all keywords. Enter the following
command to issue a list of all processes sorted by memory usage:
>
ps ax --format pid,rss,cmd --sort rss
PID RSS CMD
PID RSS CMD
2 0 [kthreadd]
3 0 [ksoftirqd/0]
4 0 [kworker/0:0]
5 0 [kworker/0:0H]
6 0 [kworker/u2:0]
7 0 [migration/0]
8 0 [rcu_bh]
[...]
12518 22996 /usr/lib/gnome-settings-daemon-3.0/gnome-settings-daemon
12626 23540 /usr/bin/nautilus --no-default-window
12305 32188 /usr/bin/Xorg :0 -background none -verbose
12594 164900 /usr/bin/gnome-shell
ps
calls #ps aux
--sort COLUMN
Sort the output by COLUMN. Replace COLUMN with
pmem
for physical memory ratiopcpu
for CPU ratiorss
for resident set size (non-swapped physical memory)ps axo pid,%cpu,rss,vsz,args,wchan
Shows every process, their PID, CPU usage ratio, memory size (resident and virtual), name, and their syscall.
ps axfo pid,args
Show a process tree.
2.3.3 Process tree: pstree
#
The command pstree
produces a list of processes in
the form of a tree:
>
pstree
systemd---accounts-daemon---{gdbus}
| |-{gmain}
|-at-spi-bus-laun---dbus-daemon
| |-{dconf worker}
| |-{gdbus}
| |-{gmain}
|-at-spi2-registr---{gdbus}
|-cron
|-2*[dbus-daemon]
|-dbus-launch
|-dconf-service---{gdbus}
| |-{gmain}
|-gconfd-2
|-gdm---gdm-simple-slav---Xorg
| | |-gdm-session-wor---gnome-session---gnome-setti+
| | | | |-gnome-shell+++
| | | | |-{dconf work+
| | | | |-{gdbus}
| | | | |-{gmain}
| | | |-{gdbus}
| | | |-{gmain}
| | |-{gdbus}
| | |-{gmain}
| |-{gdbus}
| |-{gmain}
[...]
The parameter -p
adds the process ID to a given name.
To have the command lines displayed as well, use the -a
parameter:
2.3.4 Table of processes: top
#
The command top
(an abbreviation of “table of
processes”) displays a list of processes that is refreshed every
two seconds. To terminate the program, press Q. The
parameter -n 1
terminates the program after a single
display of the process list. The following is an example output of the
command top -n 1
:
>
top -n 1
Tasks: 128 total, 1 running, 127 sleeping, 0 stopped, 0 zombie
%Cpu(s): 2.4 us, 1.2 sy, 0.0 ni, 96.3 id, 0.1 wa, 0.0 hi, 0.0 si, 0.0 st
KiB Mem: 1535508 total, 699948 used, 835560 free, 880 buffers
KiB Swap: 1541116 total, 0 used, 1541116 free. 377000 cached Mem
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
1 root 20 0 116292 4660 2028 S 0.000 0.303 0:04.45 systemd
2 root 20 0 0 0 0 S 0.000 0.000 0:00.00 kthreadd
3 root 20 0 0 0 0 S 0.000 0.000 0:00.07 ksoftirqd+
5 root 0 -20 0 0 0 S 0.000 0.000 0:00.00 kworker/0+
6 root 20 0 0 0 0 S 0.000 0.000 0:00.00 kworker/u+
7 root rt 0 0 0 0 S 0.000 0.000 0:00.00 migration+
8 root 20 0 0 0 0 S 0.000 0.000 0:00.00 rcu_bh
9 root 20 0 0 0 0 S 0.000 0.000 0:00.24 rcu_sched
10 root rt 0 0 0 0 S 0.000 0.000 0:00.01 watchdog/0
11 root 0 -20 0 0 0 S 0.000 0.000 0:00.00 khelper
12 root 20 0 0 0 0 S 0.000 0.000 0:00.00 kdevtmpfs
13 root 0 -20 0 0 0 S 0.000 0.000 0:00.00 netns
14 root 0 -20 0 0 0 S 0.000 0.000 0:00.00 writeback
15 root 0 -20 0 0 0 S 0.000 0.000 0:00.00 kintegrit+
16 root 0 -20 0 0 0 S 0.000 0.000 0:00.00 bioset
17 root 0 -20 0 0 0 S 0.000 0.000 0:00.00 crypto
18 root 0 -20 0 0 0 S 0.000 0.000 0:00.00 kblockd
By default the output is sorted by CPU usage (column Shift–P). Use the following key combinations to change the sort field:
, shortcutShift–M: Resident Memory ( ) |
Shift–N: Process ID ( ) |
Shift–T: Time ( ) |
To use any other field for sorting, press F and select a field from the list. To toggle the sort order, Use Shift–R.
The parameter -U UID
monitors only the processes associated with a particular user. Replace
UID with the user ID of the user. Use
top -U $(id -u)
to show processes of the current user
2.3.5 IBM Z hypervisor monitor: hyptop
#
hyptop
provides a dynamic real-time view of an
IBM Z hypervisor environment, using the kernel infrastructure via
debugfs. It works with either the z/VM or the LPAR hypervisor. Depending
on the available data it, for example, shows CPU and memory consumption
of active LPARs or z/VM guests. It provides a curses based user
interface similar to the top
command.
hyptop
provides two windows:
You can run hyptop
in interactive mode (default) or
in batch mode with the -b
option. Help in the
interactive mode is available by pressing ? after
hyptop
is started.
Output for the
window under LPAR:12:30:48 | CPU-T: IFL(18) CP(3) UN(3) ?=help system #cpu cpu mgm Cpu+ Mgm+ online (str) (#) (%) (%) (hm) (hm) (dhm) H05LP30 10 461.14 10.18 1547:41 8:15 11:05:59 H05LP33 4 133.73 7.57 220:53 6:12 11:05:54 H05LP50 4 99.26 0.01 146:24 0:12 10:04:24 H05LP02 1 99.09 0.00 269:57 0:00 11:05:58 TRX2CFA 1 2.14 0.03 3:24 0:04 11:06:01 H05LP13 6 1.36 0.34 4:23 0:54 11:05:56 TRX1 19 1.22 0.14 13:57 0:22 11:06:01 TRX2 20 1.16 0.11 26:05 0:25 11:06:00 H05LP55 2 0.00 0.00 0:22 0:00 11:05:52 H05LP56 3 0.00 0.00 0:00 0:00 11:05:52 413 823.39 23.86 3159:57 38:08 11:06:01
Output for the "sys_list" window under z/VM:
12:32:21 | CPU-T: UN(16) ?=help system #cpu cpu Cpu+ online memuse memmax wcur (str) (#) (%) (hm) (dhm) (GiB) (GiB) (#) T6360004 6 100.31 959:47 53:05:20 1.56 2.00 100 T6360005 2 0.44 1:11 3:02:26 0.42 0.50 100 T6360014 2 0.27 0:45 10:18:41 0.54 0.75 100 DTCVSW1 1 0.00 0:00 53:16:42 0.01 0.03 100 T6360002 6 0.00 166:26 40:19:18 1.87 2.00 100 OPERATOR 1 0.00 0:00 53:16:42 0.00 0.03 100 T6360008 2 0.00 0:37 30:22:55 0.32 0.75 100 T6360003 6 0.00 3700:57 53:03:09 4.00 4.00 100 NSLCF1 1 0.00 0:02 53:16:41 0.03 0.25 500 EREP 1 0.00 0:00 53:16:42 0.00 0.03 100 PERFSVM 1 0.00 0:53 2:21:12 0.04 0.06 0 TCPIP 1 0.00 0:01 53:16:42 0.01 0.12 3000 DATAMOVE 1 0.00 0:05 53:16:42 0.00 0.03 100 DIRMAINT 1 0.00 0:04 53:16:42 0.01 0.03 100 DTCVSW2 1 0.00 0:00 53:16:42 0.01 0.03 100 RACFVM 1 0.00 0:00 53:16:42 0.01 0.02 100 75 101.57 5239:47 53:16:42 15.46 22.50 3000
Output for the
window under LPAR:14:08:41 | H05LP30 | CPU-T: IFL(18) CP(3) UN(3) ? = help cpuid type cpu mgm visual. (#) (str) (%) (%) (vis) 0 IFL 96.91 1.96 |############################################ | 1 IFL 81.82 1.46 |##################################### | 2 IFL 88.00 2.43 |######################################## | 3 IFL 92.27 1.29 |########################################## | 4 IFL 83.32 1.05 |##################################### | 5 IFL 92.46 2.59 |########################################## | 6 IFL 0.00 0.00 | | 7 IFL 0.00 0.00 | | 8 IFL 0.00 0.00 | | 9 IFL 0.00 0.00 | | 534.79 10.78
Output for the
window under z/VM:15:46:57 | T6360003 | CPU-T: UN(16) ? = help cpuid cpu visual (#) (%) (vis) 0 548.72 |######################################### | 548.72
2.3.6 A top-like I/O monitor: iotop
#
The iotop
utility displays a table of I/O usage by
processes or threads.
iotop
iotop
is not installed by default. You need to
install it manually with zypper in iotop
as
root
.
iotop
displays columns for the I/O bandwidth read and
written by each process during the sampling period. It also displays the
percentage of time the process spent while swapping in and while waiting
on I/O. For each process, its I/O priority (class/level) is shown. In
addition, the total I/O bandwidth read and written during the sampling
period is displayed at the top of the interface.
The ← and → keys change the sorting.
R reverses the sort order.
O toggles between showing all processes and threads (default view) and showing only those doing I/O. (This function is similar to adding
--only
on command line.)P toggles between showing threads (default view) and processes. (This function is similar to
--only
.)A toggles between showing the current I/O bandwidth (default view) and accumulated I/O operations since
iotop
was started. (This function is similar to--accumulated
.)I lets you change the priority of a thread or a process's threads.
Q quits
iotop
.Pressing any other key will force a refresh.
Following is an example output of the command iotop
--only
, while find
and
emacs
are running:
#
iotop --only
Total DISK READ: 50.61 K/s | Total DISK WRITE: 11.68 K/s
TID PRIO USER DISK READ DISK WRITE SWAPIN IO> COMMAND
3416 be/4 tux 50.61 K/s 0.00 B/s 0.00 % 4.05 % find /
275 be/3 root 0.00 B/s 3.89 K/s 0.00 % 2.34 % [jbd2/sda2-8]
5055 be/4 tux 0.00 B/s 3.89 K/s 0.00 % 0.04 % emacs
iotop
can be also used in a batch mode
(-b
) and its output stored in a file for later
analysis. For a complete set of options, see the manual page
(man 8 iotop
).
2.3.7 Modify a process's niceness: nice
and renice
#
The kernel determines which processes require more CPU time than others
by the process's nice level, also called niceness. The higher the
“nice” level of a process is, the less CPU time it will
take from other processes. Nice levels range from -20 (the least
“nice” level) to 19. Negative values can only be set by
root
.
Adjusting the niceness level is useful when running a non time-critical process that lasts long and uses large amounts of CPU time. For example, compiling a kernel on a system that also performs other tasks. Making such a process “nicer”, ensures that the other tasks, for example a Web server, will have a higher priority.
Calling nice
without any parameters prints the
current niceness:
>
nice
0
Running nice
COMMAND
increments the current nice level for the given command by 10. Using
nice
-n
LEVEL
COMMAND lets you specify a new niceness
relative to the current one.
To change the niceness of a running process, use
renice
PRIORITY -p
PROCESS_ID
, for example:
>
renice +5 3266
To renice all processes owned by a specific user, use the option
-u USER
.
Process groups are reniced by the option -g PROCESS_GROUP_ID
.
2.4 Memory #
2.4.1 Memory usage: free
#
The utility free
examines RAM and swap usage. Details
of both free and used memory and swap areas are shown:
>
free
total used free shared buffers cached
Mem: 32900500 32703448 197052 0 255668 5787364
-/+ buffers/cache: 26660416 6240084
Swap: 2046972 304680 1742292
The options -b
, -k
,
-m
, -g
show the output in bytes, KB,
MB, or GB, respectively. The parameter -s delay
ensures
that the display is refreshed every DELAY
seconds. For example, free -s 1.5
produces an update
every 1.5 seconds.
2.4.2 Detailed memory usage: /proc/meminfo
#
Use /proc/meminfo
to get more detailed information
on memory usage than with free
. Actually
free
uses some data from this file. See an
example output from a 64-bit system below. Note that it slightly differs
on 32-bit systems because of different memory management:
MemTotal: 1942636 kB MemFree: 1294352 kB MemAvailable: 1458744 kB Buffers: 876 kB Cached: 278476 kB SwapCached: 0 kB Active: 368328 kB Inactive: 199368 kB Active(anon): 288968 kB Inactive(anon): 10568 kB Active(file): 79360 kB Inactive(file): 188800 kB Unevictable: 80 kB Mlocked: 80 kB SwapTotal: 2103292 kB SwapFree: 2103292 kB Dirty: 44 kB Writeback: 0 kB AnonPages: 288592 kB Mapped: 70444 kB Shmem: 11192 kB Slab: 40916 kB SReclaimable: 17712 kB SUnreclaim: 23204 kB KernelStack: 2000 kB PageTables: 10996 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 3074608 kB Committed_AS: 1407208 kB VmallocTotal: 34359738367 kB VmallocUsed: 145996 kB VmallocChunk: 34359588844 kB HardwareCorrupted: 0 kB AnonHugePages: 86016 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 79744 kB DirectMap2M: 2017280 kB
These entries stand for the following:
Total amount of RAM.
Amount of unused RAM.
Estimate of how much memory is available for starting new applications without swapping.
File buffer cache in RAM containing file system metadata.
Page cache in RAM. This excludes buffer cache and swap cache, but includes
memory.Page cache for swapped-out memory.
- , ,
Recently used memory that will not be reclaimed unless necessary or on explicit request.
is the sum of and :- , ,
Less recently used memory that will usually be reclaimed first.
is the sum of and :Amount of memory that cannot be reclaimed (for example, because it is
or used as a RAM disk).Amount of memory that is backed by the
mlock
system call.mlock
allows processes to define which part of physical RAM their virtual memory should be mapped to. However,mlock
does not guarantee this placement.Amount of swap space.
Amount of unused swap space.
Amount of memory waiting to be written to disk, because it contains changes compared to the backing storage. Dirty data can be explicitly synchronized either by the application or by the kernel after a short delay. A large amount of dirty data may take considerable time to write to disk resulting in stalls. The total amount of dirty data that can exist at any time can be controlled with the
sysctl
parametersvm.dirty_ratio
orvm.dirty_bytes
(refer to Section 16.1.5, “Writeback” for more details).Amount of memory that is currently being written to disk.
Memory claimed with the
mmap
system call.Memory shared between groups of processes, such as IPC data,
tmpfs
data, and shared anonymous memory.Memory allocation for internal data structures of the kernel.
Slab section that can be reclaimed, such as caches (inode, dentry, etc.).
Slab section that cannot be reclaimed.
Amount of kernel space memory used by applications (through system calls).
Amount of memory dedicated to page tables of all processes.
NFS pages that have already been sent to the server, but are not yet committed there.
Memory used for bounce buffers of block devices.
Memory used by FUSE for temporary writeback buffers.
Amount of memory available to the system based on the overcommit ratio setting. This is only enforced if strict overcommit accounting is enabled.
An approximation of the total amount of memory (RAM and swap) that the current workload would need in the worst case.
Amount of allocated kernel virtual address space.
Amount of used kernel virtual address space.
The largest contiguous block of available kernel virtual address space.
Amount of failed memory (can only be detected when using ECC RAM).
Anonymous hugepages that are mapped into user space page tables. These are allocated transparently for processes without being specifically requested, therefore they are also known as transparent hugepages (THP).
Number of preallocated hugepages for use by
SHM_HUGETLB
andMAP_HUGETLB
or through thehugetlbfs
file system, as defined in/proc/sys/vm/nr_hugepages
.Number of hugepages available.
Number of hugepages that are committed.
Number of hugepages available beyond “surplus”), as defined in
(/proc/sys/vm/nr_overcommit_hugepages
.Size of a hugepage—on AMD64/Intel 64 the default is 2048 KB.
- etc.
Amount of kernel memory that is mapped to pages with a given size (in the example: 4 kB).
2.4.3 Process memory usage: smaps #
Exactly determining how much memory a certain process is consuming is
not possible with standard tools like top
or
ps
. Use the smaps subsystem, introduced in kernel
2.6.14, if you need exact data. It can be found at
/proc/PID/smaps
and
shows you the number of clean and dirty memory pages the process with
the ID PID is using at that time. It
differentiates between shared and private memory, so you can see
how much memory the process is using without including memory shared
with other processes. For more information see
/usr/src/linux/Documentation/filesystems/proc.txt
(requires the package
kernel-source
to be
installed).
smaps is expensive to read. Therefore it is not recommended to monitor it regularly, but only when closely monitoring a certain process.
2.4.4 numaTOP #
numaTOP is a tool for NUMA (Non-uniform Memory Access) systems. The tool helps to identify NUMA-related performance bottlenecks by providing real-time analysis of a NUMA system.
Generally speaking, numaTOP allows you to identify and investigate processes and threads with poor locality (that is poor ratio of local versus remote memory usage) by analyzing the number of Remote Memory Accesses (RMA), the number of Local Memory Accesses (LMA), and the RMA/LMA ratio.
numaTOP is supported on PowerPC and the following Intel Xeon processors: 5500-series, 6500/7500-series, 5600-series, E7-x8xx-series, and E5-16xx/24xx/26xx/46xx-series.
numaTOP is available in the official software repositories, and
you can install the tool using the sudo zypper in
numatop
command. To launch numaTOP, run the
numatop
command. To get an overview of
numaTOP functionality and usage, use the man
numatop
command.
2.5 Networking #
In case the network bandwidth is lower than expected, you should first check if any traffic shaping rules are active for your network segment.
2.5.1 Basic network diagnostics: ip
#
ip
is a powerful tool to set up and control network
interfaces. You can also use it to quickly view basic statistics about
network interfaces of the system. For example, whether the interface is
up or how many errors, dropped packets, or packet collisions there are.
If you run ip
with no additional parameter, it
displays a help output. To list all network interfaces, enter
ip addr show
(or abbreviated as ip
a
). ip addr show up
lists only running
network interfaces. ip -s link show
DEVICE lists statistics for the specified
interface only:
#
ip -s link show br0
6: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT
link/ether 00:19:d1:72:d4:30 brd ff:ff:ff:ff:ff:ff
RX: bytes packets errors dropped overrun mcast
6346104756 9265517 0 10860 0 0
TX: bytes packets errors dropped carrier collsns
3996204683 3655523 0 0 0 0
ip
can also show interfaces
(link
), routing tables (route
), and
much more—refer to man 8 ip
for details.
#
ip route
default via 192.168.2.1 dev eth1
192.168.2.0/24 dev eth0 proto kernel scope link src 192.168.2.100
192.168.2.0/24 dev eth1 proto kernel scope link src 192.168.2.101
192.168.2.0/24 dev eth2 proto kernel scope link src 192.168.2.102
#
ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000
link/ether 52:54:00:44:30:51 brd ff:ff:ff:ff:ff:ff
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000
link/ether 52:54:00:a3:c1:fb brd ff:ff:ff:ff:ff:ff
4: eth2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000
link/ether 52:54:00:32:a4:09 brd ff:ff:ff:ff:ff:ff
2.5.2
Show the network usage of processes: nethogs
#
In some cases, for example if the network traffic suddenly becomes very
high, it is desirable to quickly find out which application(s) is/are
causing the traffic. nethogs
, a tool with a design
similar to top
, shows incoming and outgoing traffic for
all relevant processes:
PID USER PROGRAM DEV SENT RECEIVED 27145 root zypper eth0 5.719 391.749 KB/sec ? root ..0:113:80c0:8080:10:160:0:100:30015 0.102 2.326 KB/sec 26635 tux /usr/lib64/firefox/firefox eth0 0.026 0.026 KB/sec ? root ..0:113:80c0:8080:10:160:0:100:30045 0.000 0.021 KB/sec ? root ..0:113:80c0:8080:10:160:0:100:30045 0.000 0.018 KB/sec ? root ..0:113:80c0:8080:10:160:0:100:30015 0.000 0.018 KB/sec ? root ..0:113:80c0:8080:10:160:0:100:30045 0.000 0.017 KB/sec ? root ..0:113:80c0:8080:10:160:0:100:30045 0.000 0.017 KB/sec ? root ..0:113:80c0:8080:10:160:0:100:30045 0.069 0.000 KB/sec ? root unknown TCP 0.000 0.000 KB/sec TOTAL 5.916 394.192 KB/sec
Like in top
, nethogs
features
interactive commands:
M: cycle between display modes (kb/s, kb, b, mb) |
R: sort by |
S: sort by |
Q: quit |
2.5.3 Ethernet cards in detail: ethtool #
ethtool
can display and change detailed aspects of
your Ethernet network device. By default it prints the current setting
of the specified device.
#
ethtool eth0
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
[...]
Link detected: yes
The following table shows ethtool
options that you
can use to query the device for specific information:
ethtool
#
|
it queries the device for |
---|---|
-a |
pause parameter information |
-c |
interrupt coalescing information |
-g |
Rx/Tx (receive/transmit) ring parameter information |
-i |
associated driver information |
-k |
offload information |
-S |
NIC and driver-specific statistics |
2.5.4 Show the network status: ss
#
ss
is a tool to dump socket statistics and replaces
the netstat
command. To list all
connections use ss
without parameters:
#
ss
Netid State Recv-Q Send-Q Local Address:Port Peer Address:Port
u_str ESTAB 0 0 * 14082 * 14083
u_str ESTAB 0 0 * 18582 * 18583
u_str ESTAB 0 0 * 19449 * 19450
u_str ESTAB 0 0 @/tmp/dbus-gmUUwXABPV 18784 * 18783
u_str ESTAB 0 0 /var/run/dbus/system_bus_socket 19383 * 19382
u_str ESTAB 0 0 @/tmp/dbus-gmUUwXABPV 18617 * 18616
u_str ESTAB 0 0 @/tmp/dbus-58TPPDv8qv 19352 * 19351
u_str ESTAB 0 0 * 17658 * 17657
u_str ESTAB 0 0 * 17693 * 17694
[..]
To show all network ports currently open, use the following command:
#
ss -l
Netid State Recv-Q Send-Q Local Address:Port Peer Address:Port
nl UNCONN 0 0 rtnl:4195117 *
nl UNCONN 0 0 rtnl:wickedd-auto4/811 *
nl UNCONN 0 0 rtnl:wickedd-dhcp4/813 *
nl UNCONN 0 0 rtnl:4195121 *
nl UNCONN 0 0 rtnl:4195115 *
nl UNCONN 0 0 rtnl:wickedd-dhcp6/814 *
nl UNCONN 0 0 rtnl:kernel *
nl UNCONN 0 0 rtnl:wickedd/817 *
nl UNCONN 0 0 rtnl:4195118 *
nl UNCONN 0 0 rtnl:nscd/706 *
nl UNCONN 4352 0 tcpdiag:ss/2381 *
[...]
When displaying network connections, you can specify the socket type to
display: TCP (-t
) or UDP (-u
) for
example. The -p
option shows the PID and name of the
program to which each socket belongs.
The following example lists all TCP connections and the programs using
these connections. The -a
option make sure all
established connections (listening and non-listening) are shown. The
-p
option shows the PID and name of the program to
which each socket belongs.
#
ss -t -a -p
State Recv-Q Send-Q Local Address:Port Peer Address:Port
LISTEN 0 128 *:ssh *:* users:(("sshd",1551,3))
LISTEN 0 100 127.0.0.1:smtp *:* users:(("master",1704,13))
ESTAB 0 132 10.120.65.198:ssh 10.120.4.150:55715 users:(("sshd",2103,5))
LISTEN 0 128 :::ssh :::* users:(("sshd",1551,4))
LISTEN 0 100 ::1:smtp :::* users:(("master",1704,14))
2.6 The /proc
file system #
The /proc
file system is a pseudo file system in
which the kernel reserves important information in the form of virtual
files. For example, display the CPU type with this command:
>
cat /proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 30
model name : Intel(R) Core(TM) i5 CPU 750 @ 2.67GHz
stepping : 5
microcode : 0x6
cpu MHz : 1197.000
cache size : 8192 KB
physical id : 0
siblings : 4
core id : 0
cpu cores : 4
apicid : 0
initial apicid : 0
fpu : yes
fpu_exception : yes
cpuid level : 11
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp lm constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni dtes64 monitor ds_cpl vmx smx est tm2 ssse3 cx16 xtpr pdcm sse4_1 sse4_2 popcnt lahf_lm ida dtherm tpr_shadow vnmi flexpriority ept vpid
bogomips : 5333.85
clflush size : 64
cache_alignment : 64
address sizes : 36 bits physical, 48 bits virtual
power management:
[...]
Detailed information about the processor on the AMD64/Intel 64 architecture is
also available by running x86info
.
Query the allocation and use of interrupts with the following command:
>
cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3
0: 121 0 0 0 IO-APIC-edge timer
8: 0 0 0 1 IO-APIC-edge rtc0
9: 0 0 0 0 IO-APIC-fasteoi acpi
16: 0 11933 0 0 IO-APIC-fasteoi ehci_hcd:+
18: 0 0 0 0 IO-APIC-fasteoi i801_smbus
19: 0 117978 0 0 IO-APIC-fasteoi ata_piix,+
22: 0 0 3275185 0 IO-APIC-fasteoi enp5s1
23: 417927 0 0 0 IO-APIC-fasteoi ehci_hcd:+
40: 2727916 0 0 0 HPET_MSI-edge hpet2
41: 0 2749134 0 0 HPET_MSI-edge hpet3
42: 0 0 2759148 0 HPET_MSI-edge hpet4
43: 0 0 0 2678206 HPET_MSI-edge hpet5
45: 0 0 0 0 PCI-MSI-edge aerdrv, P+
46: 0 0 0 0 PCI-MSI-edge PCIe PME,+
47: 0 0 0 0 PCI-MSI-edge PCIe PME,+
48: 0 0 0 0 PCI-MSI-edge PCIe PME,+
49: 0 0 0 387 PCI-MSI-edge snd_hda_i+
50: 933117 0 0 0 PCI-MSI-edge nvidia
NMI: 2102 2023 2031 1920 Non-maskable interrupts
LOC: 92 71 57 41 Local timer interrupts
SPU: 0 0 0 0 Spurious interrupts
PMI: 2102 2023 2031 1920 Performance monitoring int+
IWI: 47331 45725 52464 46775 IRQ work interrupts
RTR: 2 0 0 0 APIC ICR read retries
RES: 472911 396463 339792 323820 Rescheduling interrupts
CAL: 48389 47345 54113 50478 Function call interrupts
TLB: 28410 26804 24389 26157 TLB shootdowns
TRM: 0 0 0 0 Thermal event interrupts
THR: 0 0 0 0 Threshold APIC interrupts
MCE: 0 0 0 0 Machine check exceptions
MCP: 40 40 40 40 Machine check polls
ERR: 0
MIS: 0
The address assignment of executables and libraries is contained in the
maps
file:
>
cat /proc/self/maps
08048000-0804c000 r-xp 00000000 03:03 17753 /bin/cat
0804c000-0804d000 rw-p 00004000 03:03 17753 /bin/cat
0804d000-0806e000 rw-p 0804d000 00:00 0 [heap]
b7d27000-b7d5a000 r--p 00000000 03:03 11867 /usr/lib/locale/en_GB.utf8/
b7d5a000-b7e32000 r--p 00000000 03:03 11868 /usr/lib/locale/en_GB.utf8/
b7e32000-b7e33000 rw-p b7e32000 00:00 0
b7e33000-b7f45000 r-xp 00000000 03:03 8837 /lib/libc-2.3.6.so
b7f45000-b7f46000 r--p 00112000 03:03 8837 /lib/libc-2.3.6.so
b7f46000-b7f48000 rw-p 00113000 03:03 8837 /lib/libc-2.3.6.so
b7f48000-b7f4c000 rw-p b7f48000 00:00 0
b7f52000-b7f53000 r--p 00000000 03:03 11842 /usr/lib/locale/en_GB.utf8/
[...]
b7f5b000-b7f61000 r--s 00000000 03:03 9109 /usr/lib/gconv/gconv-module
b7f61000-b7f62000 r--p 00000000 03:03 9720 /usr/lib/locale/en_GB.utf8/
b7f62000-b7f76000 r-xp 00000000 03:03 8828 /lib/ld-2.3.6.so
b7f76000-b7f78000 rw-p 00013000 03:03 8828 /lib/ld-2.3.6.so
bfd61000-bfd76000 rw-p bfd61000 00:00 0 [stack]
ffffe000-fffff000 ---p 00000000 00:00 0 [vdso]
A lot more information can be obtained from the /proc file system. Some important files and their contents are:
/proc/devices
Available devices
/proc/modules
Kernel modules loaded
/proc/cmdline
Kernel command line
/proc/meminfo
Detailed information about memory usage
/proc/config.gz
gzip
-compressed configuration file of the kernel currently running- /proc/PID/
Find information about processes currently running in the
/proc/
NNN directories, where NNN is the process ID (PID) of the relevant process. Every process can find its own characteristics in/proc/self/
.
Further information is available in the text file
/usr/src/linux/Documentation/filesystems/proc.txt
(this file is available when the package
kernel-source
is installed).
2.6.1 procinfo
#
Important information from the /proc
file system is
summarized by the command procinfo
:
>
procinfo
Linux 3.11.10-17-desktop (geeko@buildhost) (gcc 4.8.1 20130909) #1 4CPU [jupiter.example.com]
Memory: Total Used Free Shared Buffers Cached
Mem: 8181908 8000632 181276 0 85472 2850872
Swap: 10481660 1576 10480084
Bootup: Mon Jul 28 09:54:13 2014 Load average: 1.61 0.85 0.74 2/904 25949
user : 1:54:41.84 12.7% page in : 2107312 disk 1: 52212r 20199w
nice : 0:00:00.46 0.0% page out: 1714461 disk 2: 19387r 10928w
system: 0:25:38.00 2.8% page act: 466673 disk 3: 548r 10w
IOwait: 0:04:16.45 0.4% page dea: 272297
hw irq: 0:00:00.42 0.0% page flt: 105754526
sw irq: 0:01:26.48 0.1% swap in : 0
idle : 12:14:43.65 81.5% swap out: 394
guest : 0:02:18.59 0.2%
uptime: 3:45:22.24 context : 99809844
irq 0: 121 timer irq 41: 3238224 hpet3
irq 8: 1 rtc0 irq 42: 3251898 hpet4
irq 9: 0 acpi irq 43: 3156368 hpet5
irq 16: 14589 ehci_hcd:usb1 irq 45: 0 aerdrv, PCIe PME
irq 18: 0 i801_smbus irq 46: 0 PCIe PME, pciehp
irq 19: 124861 ata_piix, ata_piix, f irq 47: 0 PCIe PME, pciehp
irq 22: 3742817 enp5s1 irq 48: 0 PCIe PME, pciehp
irq 23: 479248 ehci_hcd:usb2 irq 49: 387 snd_hda_intel
irq 40: 3216894 hpet2 irq 50: 1088673 nvidia
To see all the information, use the parameter -a
. The
parameter -nN
produces updates of the information every
N seconds. In this case, terminate the
program by pressing Q.
By default, the cumulative values are displayed. The parameter
-d
produces the differential values. procinfo
-dn5
displays the values that have changed in the last five
seconds:
2.6.2 System control parameters: /proc/sys/
#
System control parameters are used to modify the Linux kernel parameters
at runtime. They reside in /proc/sys/
and can be
viewed and modified with the sysctl
command. To list
all parameters, run sysctl
-a
. A
single parameter can be listed with sysctl
PARAMETER_NAME.
Parameters are grouped into categories and can be listed with
sysctl
CATEGORY or by
listing the contents of the respective directories. The most important
categories are listed below. The links to further readings require the
installation of the package
kernel-source
.
sysctl dev
(/proc/sys/dev/
)Device-specific information.
sysctl fs
(/proc/sys/fs/
)Used file handles, quotas, and other file system-oriented parameters. For details see
/usr/src/linux/Documentation/sysctl/fs.txt
.sysctl kernel
(/proc/sys/kernel/
)Information about the task scheduler, system shared memory, and other kernel-related parameters. For details see
/usr/src/linux/Documentation/sysctl/kernel.txt
sysctl net
(/proc/sys/net/
)Information about network bridges, and general network parameters (mainly the
ipv4/
subdirectory). For details see/usr/src/linux/Documentation/sysctl/net.txt
sysctl vm
(/proc/sys/vm/
)Entries in this path relate to information about the virtual memory, swapping, and caching. For details see
/usr/src/linux/Documentation/sysctl/vm.txt
To set or change a parameter for the current session, use the command
sysctl
-w
PARAMETER=VALUE.
To permanently change a setting, add a line
PARAMETER=VALUE to
/etc/sysctl.conf
.
2.7 Hardware information #
2.7.1 PCI resources: lspci
#
Most operating systems require root user privileges to grant access to the computer's PCI configuration.
The command lspci
lists the PCI resources:
#
lspci
00:00.0 Host bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE \
DRAM Controller/Host-Hub Interface (rev 01)
00:01.0 PCI bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE \
Host-to-AGP Bridge (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM \
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM \
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM \
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM \
(ICH4/ICH4-M) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 81)
00:1f.0 ISA bridge: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) \
LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE \
Controller (rev 01)
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) \
SMBus Controller (rev 01)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM \
(ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01)
01:00.0 VGA compatible controller: Matrox Graphics, Inc. G400/G450 (rev 85)
02:08.0 Ethernet controller: Intel Corporation 82801DB PRO/100 VE (LOM) \
Ethernet Controller (rev 81)
Using -v
results in a more detailed listing:
#
lspci -v
[...]
00:03.0 Ethernet controller: Intel Corporation 82540EM Gigabit Ethernet \
Controller (rev 02)
Subsystem: Intel Corporation PRO/1000 MT Desktop Adapter
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 19
Memory at f0000000 (32-bit, non-prefetchable) [size=128K]
I/O ports at d010 [size=8]
Capabilities: [dc] Power Management version 2
Capabilities: [e4] PCI-X non-bridge device
Kernel driver in use: e1000
Kernel modules: e1000
Information about device name resolution is obtained from the file
/usr/share/pci.ids
. PCI IDs not listed in this file
are marked “Unknown device.”
The parameter -vv
produces all the information that
could be queried by the program. To view the pure numeric values, use
the parameter -n
.
2.7.2 USB devices: lsusb
#
The command lsusb
lists all USB devices. With the
option -v
, print a more detailed list. The detailed
information is read from the directory
/proc/bus/usb/
. The following is the output of
lsusb
with these USB devices attached: hub, memory
stick, hard disk and mouse.
#
lsusb
Bus 004 Device 007: ID 0ea0:2168 Ours Technology, Inc. Transcend JetFlash \
2.0 / Astone USB Drive
Bus 004 Device 006: ID 04b4:6830 Cypress Semiconductor Corp. USB-2.0 IDE \
Adapter
Bus 004 Device 005: ID 05e3:0605 Genesys Logic, Inc.
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 005: ID 046d:c012 Logitech, Inc. Optical Mouse
Bus 001 Device 001: ID 0000:0000
2.7.3
Monitoring and tuning the thermal subsystem: tmon
#
tmon
is a tool to help visualize, tune, and test the
complex thermal subsystem. When started without parameters,
tmon
runs in monitoring mode:
┌──────THERMAL ZONES(SENSORS)──────────────────────────────┐ │Thermal Zones: acpitz00 │ │Trip Points: PC │ └──────────────────────────────────────────────────────────┘ ┌─────────── COOLING DEVICES ──────────────────────────────┐ │ID Cooling Dev Cur Max Thermal Zone Binding │ │00 Processor 0 3 ││││││││││││ │ │01 Processor 0 3 ││││││││││││ │ │02 Processor 0 3 ││││││││││││ │ │03 Processor 0 3 ││││││││││││ │ │04 intel_powerc -1 50 ││││││││││││ │ └──────────────────────────────────────────────────────────┘ ┌──────────────────────────────────────────────────────────┐ │ 10 20 30 40 │ │acpitz 0:[ 8][>>>>>>>>>P9 C31 │ └──────────────────────────────────────────────────────────┘ ┌────────────────── CONTROLS ──────────────────────────────┐ │PID gain: kp=0.36 ki=5.00 kd=0.19 Output 0.00 │ │Target Temp: 65.0C, Zone: 0, Control Device: None │ └──────────────────────────────────────────────────────────┘ Ctrl-c - Quit TAB - Tuning
For detailed information on how to interpret the data, how to log thermal
data and how to use tmon
to test and tune cooling
devices and sensors, refer to the man page: man 8
tmon
. The package tmon is not installed by
default.
2.7.4 MCELog: machine check exceptions (MCE) #
This tool is only available on AMD64/Intel 64 systems.
The mcelog
package logs and
parses/translates Machine Check Exceptions (MCE) on hardware errors, including
I/O, CPU, and memory errors. In addition, mcelog handles predictive bad page
offlining and automatic core offlining when cache errors happen.
Formerly this was managed by a cron job executed hourly. Now hardware
errors are immediately processed by an mcelog daemon.
SUSE Linux Enterprise Server supports AMD's Scalable Machine Check Architecture (Scalable MCA). Scalable MCA improves hardware error reporting in AMD Zen processors. It expands information logged in MCA banks for improved error handling and better diagnosability.
mcelog
captures MCA messages
(rasdaemon
and
dmesg
also capture MCA messages).
See section 3.1, Machine Check Architecture of
Processor Programming Reference (PPR) for AMD Family
17h Model 01h, Revision B1 Processors for detailed
information,
https://developer.amd.com/wordpress/media/2017/11/54945_PPR_Family_17h_Models_00h-0Fh.pdf.
mcelog is configured in /etc/mcelog/mcelog.conf
.
Configuration options are documented in
man mcelog
, and at
https://mcelog.org/. The following example shows
only changes to the default file:
daemon = yes filter = yes filter-memory-errors = yes no-syslog = yes logfile = /var/log/mcelog run-credentials-user = root run-credentials-group = nobody client-group = root socket-path = /var/run/mcelog-client
The mcelog service is not enabled by default. The service can either be enabled and started via the YaST system services editor, or via command line:
#
systemctl enable mcelog#
systemctl start mcelog
2.7.5 AMD64/Intel 64: dmidecode: DMI table decoder #
dmidecode
shows the machine's DMI table containing
information such as serial numbers and BIOS revisions of the hardware.
#
dmidecode
# dmidecode 2.12
SMBIOS 2.5 present.
27 structures occupying 1298 bytes.
Table at 0x000EB250.
Handle 0x0000, DMI type 4, 35 bytes
Processor Information
Socket Designation: J1PR
Type: Central Processor
Family: Other
Manufacturer: Intel(R) Corporation
ID: E5 06 01 00 FF FB EB BF
Version: Intel(R) Core(TM) i5 CPU 750 @ 2.67GHz
Voltage: 1.1 V
External Clock: 133 MHz
Max Speed: 4000 MHz
Current Speed: 2667 MHz
Status: Populated, Enabled
Upgrade: Other
L1 Cache Handle: 0x0004
L2 Cache Handle: 0x0003
L3 Cache Handle: 0x0001
Serial Number: Not Specified
Asset Tag: Not Specified
Part Number: Not Specified
[..]
2.7.6 POWER: list hardware #
lshw
extracts and displays the hardware
configuration of the machine.
2.8 Files and file systems #
For file system-specific information, refer to Storage Administration Guide.
2.8.1 Determine the file type: file
#
The command file
determines the type of a file or a
list of files by checking /usr/share/misc/magic
.
>
file /usr/bin/file
/usr/bin/file: ELF 64-bit LSB executable, x86-64, version 1 (SYSV), \
for GNU/Linux 2.6.4, dynamically linked (uses shared libs), stripped
The parameter -f LIST
specifies a file with a list of file names to examine. The
-z
allows file
to look inside
compressed files:
>
file /usr/share/man/man1/file.1.gz /usr/share/man/man1/file.1.gz: gzip compressed data, from Unix, max compression>
file -z /usr/share/man/man1/file.1.gz /usr/share/man/man1/file.1.gz: troff or preprocessor input text \ (gzip compressed data, from Unix, max compression)
The parameter -i
outputs a mime type string rather than
the traditional description.
>
file -i /usr/share/misc/magic
/usr/share/misc/magic: text/plain charset=utf-8
2.8.2 File systems and their usage: mount
, df
and du
#
The command mount
shows which file system (device and
type) is mounted at which mount point:
#
mount
/dev/sda2 on / type ext4 (rw,acl,user_xattr)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
debugfs on /sys/kernel/debug type debugfs (rw)
devtmpfs on /dev type devtmpfs (rw,mode=0755)
tmpfs on /dev/shm type tmpfs (rw,mode=1777)
devpts on /dev/pts type devpts (rw,mode=0620,gid=5)
/dev/sda3 on /home type ext3 (rw)
securityfs on /sys/kernel/security type securityfs (rw)
fusectl on /sys/fs/fuse/connections type fusectl (rw)
gvfs-fuse-daemon on /home/tux/.gvfs type fuse.gvfs-fuse-daemon \
(rw,nosuid,nodev,user=tux)
Obtain information about total usage of the file systems with the
command df
. The parameter -h
(or
--human-readable
) transforms the output into a form
understandable for common users.
>
df -h
Filesystem Size Used Avail Use% Mounted on
/dev/sda2 20G 5,9G 13G 32% /
devtmpfs 1,6G 236K 1,6G 1% /dev
tmpfs 1,6G 668K 1,6G 1% /dev/shm
/dev/sda3 208G 40G 159G 20% /home
Display the total size of all the files in a given directory and its
subdirectories with the command du
. The parameter
-s
suppresses the output of detailed information and
gives only a total for each argument. -h
again
transforms the output into a human-readable form:
>
du -sh /opt
192M /opt
2.8.3 Additional information about ELF binaries #
Read the content of binaries with the readelf
utility. This even works with ELF files that were built for other
hardware architectures:
>
readelf --file-header /bin/ls
ELF Header:
Magic: 7f 45 4c 46 02 01 01 00 00 00 00 00 00 00 00 00
Class: ELF64
Data: 2's complement, little endian
Version: 1 (current)
OS/ABI: UNIX - System V
ABI Version: 0
Type: EXEC (Executable file)
Machine: Advanced Micro Devices X86-64
Version: 0x1
Entry point address: 0x402540
Start of program headers: 64 (bytes into file)
Start of section headers: 95720 (bytes into file)
Flags: 0x0
Size of this header: 64 (bytes)
Size of program headers: 56 (bytes)
Number of program headers: 9
Size of section headers: 64 (bytes)
Number of section headers: 32
Section header string table index: 31
2.8.4 File properties: stat
#
The command stat
displays file properties:
>
stat /etc/profile
File: `/etc/profile'
Size: 9662 Blocks: 24 IO Block: 4096 regular file
Device: 802h/2050d Inode: 132349 Links: 1
Access: (0644/-rw-r--r--) Uid: ( 0/ root) Gid: ( 0/ root)
Access: 2009-03-20 07:51:17.000000000 +0100
Modify: 2009-01-08 19:21:14.000000000 +0100
Change: 2009-03-18 12:55:31.000000000 +0100
The parameter --file-system
produces details of the
properties of the file system in which the specified file is located:
>
stat /etc/profile --file-system
File: "/etc/profile"
ID: d4fb76e70b4d1746 Namelen: 255 Type: ext2/ext3
Block size: 4096 Fundamental block size: 4096
Blocks: Total: 2581445 Free: 1717327 Available: 1586197
Inodes: Total: 655776 Free: 490312
2.9 User information #
2.9.1 User accessing files: fuser
#
It can be useful to determine what processes or users are currently
accessing certain files. Suppose, for example, you want to unmount a
file system mounted at /mnt
.
umount
returns "device is busy." The command
fuser
can then be used to determine what processes
are accessing the device:
>
fuser -v /mnt/*
USER PID ACCESS COMMAND
/mnt/notes.txt tux 26597 f.... less
Following termination of the less
process, which was
running on another terminal, the file system can successfully be
unmounted. When used with -k
option,
fuser
will terminate processes accessing the file as
well.
2.9.2 Who is doing what: w
#
With the command w
, find out who is logged in to the
system and what each user is doing. For example:
>
w
16:00:59 up 1 day, 2:41, 3 users, load average: 0.00, 0.01, 0.05
USER TTY FROM LOGIN@ IDLE JCPU PCPU WHAT
tux :0 console Wed13 ?xdm? 8:15 0.03s /usr/lib/gdm/gd
tux console :0 Wed13 26:41m 0.00s 0.03s /usr/lib/gdm/gd
tux pts/0 :0 Wed13 20:11 0.10s 2.89s /usr/lib/gnome-
If any users of other systems have logged in remotely, the parameter
-f
shows the computers from which they have established
the connection.
2.10 Time and date #
2.10.1 Time measurement with time
#
Determine the time spent by commands with the time
utility. This utility is available in two versions: as a Bash built-in
and as a program (/usr/bin/time
).
>
time find . > /dev/null
real 0m4.051s1
user 0m0.042s2
sys 0m0.205s3
The real time that elapsed from the command's start-up until it finished. | |
CPU time of the user as reported by the | |
CPU time of the system as reported by the |
The output of /usr/bin/time
is much more detailed.
It is recommended to run it with the -v
switch to
produce human-readable output.
/usr/bin/time -v find . > /dev/null Command being timed: "find ." User time (seconds): 0.24 System time (seconds): 2.08 Percent of CPU this job got: 25% Elapsed (wall clock) time (h:mm:ss or m:ss): 0:09.03 Average shared text size (kbytes): 0 Average unshared data size (kbytes): 0 Average stack size (kbytes): 0 Average total size (kbytes): 0 Maximum resident set size (kbytes): 2516 Average resident set size (kbytes): 0 Major (requiring I/O) page faults: 0 Minor (reclaiming a frame) page faults: 1564 Voluntary context switches: 36660 Involuntary context switches: 496 Swaps: 0 File system inputs: 0 File system outputs: 0 Socket messages sent: 0 Socket messages received: 0 Signals delivered: 0 Page size (bytes): 4096 Exit status: 0
2.11 Graph your data: RRDtool #
There are a lot of data in the world around you, which can be easily measured in time. For example, changes in the temperature, or the number of data sent or received by your computer's network interface. RRDtool can help you store and visualize such data in detailed and customizable graphs.
RRDtool is available for most Unix platforms and Linux distributions. SUSE® Linux Enterprise Server ships RRDtool as well. Install it either with YaST or by entering
zypper
install
rrdtool in the command line as root
.
There are Perl, Python, Ruby, and PHP bindings available for RRDtool, so that you can write your own monitoring scripts in your preferred scripting language.
2.11.1 How RRDtool works #
RRDtool is an abbreviation of Round Robin Database tool. Round Robin is a method for manipulating with a constant amount of data. It uses the principle of a circular buffer, where there is no end nor beginning to the data row which is being read. RRDtool uses Round Robin Databases to store and read its data.
As mentioned above, RRDtool is designed to work with data that change in time. The ideal case is a sensor which repeatedly reads measured data (like temperature, speed etc.) in constant periods of time, and then exports them in a given format. Such data are perfectly ready for RRDtool, and it is easy to process them and create the desired output.
Sometimes it is not possible to obtain the data automatically and regularly. Their format needs to be pre-processed before it is supplied to RRDtool, and often you need to manipulate RRDtool even manually.
The following is a simple example of basic RRDtool usage. It illustrates all three important phases of the usual RRDtool workflow: creating a database, updating measured values, and viewing the output.
2.11.2 A practical example #
Suppose we want to collect and view information about the memory usage in the Linux system as it changes in time. To make the example more vivid, we measure the currently free memory over a period of 40 seconds in 4-second intervals. Three applications that usually consume a lot of system memory are started and closed: the Firefox Web browser, the Evolution e-mail client, and the Eclipse development framework.
2.11.2.1 Collecting data #
RRDtool is very often used to measure and visualize network traffic. In such case, the Simple Network Management Protocol (SNMP) is used. This protocol can query network devices for relevant values of their internal counters. Exactly these values are to be stored with RRDtool. For more information on SNMP, see http://www.net-snmp.org/.
Our situation is different—we need to obtain the data
manually. A helper script free_mem.sh
repetitively
reads the current state of free memory and writes it to the standard
output.
>
cat free_mem.sh
INTERVAL=4
for steps in {1..10}
do
DATE=`date +%s`
FREEMEM=`free -b | grep "Mem" | awk '{ print $4 }'`
sleep $INTERVAL
echo "rrdtool update free_mem.rrd $DATE:$FREEMEM"
done
The time interval is set to 4 seconds, and is implemented with the
sleep
command.RRDtool accepts time information in a special format - so called Unix time. It is defined as the number of seconds since the midnight of January 1, 1970 (UTC). For example, 1272907114 represents 2010-05-03 17:18:34.
The free memory information is reported in bytes with
free
-b
. Prefer to supply basic units (bytes) instead of multiple units (like kilobytes).The line with the
echo ...
command contains the future name of the database file (free_mem.rrd
), and together creates a command line for updating RRDtool values.
After running free_mem.sh
, you see an output similar
to this:
>
sh free_mem.sh
rrdtool update free_mem.rrd 1272974835:1182994432
rrdtool update free_mem.rrd 1272974839:1162817536
rrdtool update free_mem.rrd 1272974843:1096269824
rrdtool update free_mem.rrd 1272974847:1034219520
rrdtool update free_mem.rrd 1272974851:909438976
rrdtool update free_mem.rrd 1272974855:832454656
rrdtool update free_mem.rrd 1272974859:829120512
rrdtool update free_mem.rrd 1272974863:1180377088
rrdtool update free_mem.rrd 1272974867:1179369472
rrdtool update free_mem.rrd 1272974871:1181806592
It is convenient to redirect the command's output to a file with
sh free_mem.sh > free_mem_updates.log
to simplify its future execution.
2.11.2.2 Creating the database #
Create the initial Robin Round database for our example with the following command:
>
rrdtool create free_mem.rrd --start 1272974834 --step=4 \
DS:memory:GAUGE:600:U:U RRA:AVERAGE:0.5:1:24
This command creates a file called
free_mem.rrd
for storing our measured values in a Round Robin type database.The
--start
option specifies the time (in Unix time) when the first value will be added to the database. In this example, it is one less than the first time value of thefree_mem.sh
output (1272974835).The
--step
specifies the time interval in seconds with which the measured data will be supplied to the database.The
DS:memory:GAUGE:600:U:U
part introduces a new data source for the database. It is called memory, its type is gauge, the maximum number between two updates is 600 seconds, and the minimal and maximal value in the measured range are unknown (U).RRA:AVERAGE:0.5:1:24
creates Round Robin archive (RRA) whose stored data are processed with the consolidation functions (CF) that calculates the average of data points. 3 arguments of the consolidation function are appended to the end of the line.
If no error message is displayed, then
free_mem.rrd
database is created in the current
directory:
>
ls -l free_mem.rrd
-rw-r--r-- 1 tux users 776 May 5 12:50 free_mem.rrd
2.11.2.3 Updating database values #
After the database is created, you need to fill it with the measured
data. In Section 2.11.2.1, “Collecting data”, we already
prepared the file free_mem_updates.log
which
consists of rrdtool update
commands. These commands
do the update of database values for us.
>
sh free_mem_updates.log; ls -l free_mem.rrd
-rw-r--r-- 1 tux users 776 May 5 13:29 free_mem.rrd
As you can see, the size of free_mem.rrd
remained
the same even after updating its data.
2.11.2.4 Viewing measured values #
We have already measured the values, created the database, and stored the measured value in it. Now we can play with the database, and retrieve or view its values.
To retrieve all the values from our database, enter the following on the command line:
>
rrdtool fetch free_mem.rrd AVERAGE --start 1272974830 \
--end 1272974871
memory
1272974832: nan
1272974836: 1.1729059840e+09
1272974840: 1.1461806080e+09
1272974844: 1.0807572480e+09
1272974848: 1.0030243840e+09
1272974852: 8.9019289600e+08
1272974856: 8.3162112000e+08
1272974860: 9.1693465600e+08
1272974864: 1.1801251840e+09
1272974868: 1.1799787520e+09
1272974872: nan
AVERAGE
will fetch average value points from the database, because only one data source is defined (Section 2.11.2.2, “Creating the database”) withAVERAGE
processing and no other function is available.The first line of the output prints the name of the data source as defined in Section 2.11.2.2, “Creating the database”.
The left results column represents individual points in time, while the right one represents corresponding measured average values in scientific notation.
The
nan
in the last line stands for “not a number”.
Now a graph representing the values stored in the database is drawn:
>
rrdtool graph free_mem.png \
--start 1272974830 \
--end 1272974871 \
--step=4 \
DEF:free_memory=free_mem.rrd:memory:AVERAGE \
LINE2:free_memory#FF0000 \
--vertical-label "GB" \
--title "Free System Memory in Time" \
--zoom 1.5 \
--x-grid SECOND:1:SECOND:4:SECOND:10:0:%X
free_mem.png
is the file name of the graph to be created.--start
and--end
limit the time range within which the graph will be drawn.--step
specifies the time resolution (in seconds) of the graph.The
DEF:...
part is a data definition called free_memory. Its data are read from thefree_mem.rrd
database and its data source called memory. The average value points are calculated, because no others were defined in Section 2.11.2.2, “Creating the database”.The
LINE...
part specifies properties of the line to be drawn into the graph. It is 2 pixels wide, its data come from the free_memory definition, and its color is red.--vertical-label
sets the label to be printed along the y axis, and--title
sets the main label for the whole graph.--zoom
specifies the zoom factor for the graph. This value must be greater than zero.--x-grid
specifies how to draw grid lines and their labels into the graph. Our example places them every second, while major grid lines are placed every 4 seconds. Labels are placed every 10 seconds under the major grid lines.
2.11.3 More information #
RRDtool is a very complex tool with a lot of sub-commands and command line options. Some are easy to understand, but to make it produce the results you want and fine-tune them according to your liking may require a lot of effort.
Apart from RRDtool's man page (man 1 rrdtool
) which
gives you only basic information, you should have a look at the
RRDtool home
page. There is a detailed
documentation
of the rrdtool
command and all its sub-commands.
There are also several
tutorials
to help you understand the common RRDtool workflow.
If you are interested in monitoring network traffic, have a look at MRTG (Multi Router Traffic Grapher). MRTG can graph the activity of many network devices. It can use RRDtool.