Jump to contentJump to page navigation: previous page [access key p]/next page [access key n]
documentation.suse.com / Documentation SUSE Linux Enterprise Desktop / Administration Guide / System / Managing kernel modules
Applies to SUSE Linux Enterprise Desktop 15 SP6

28 Managing kernel modules

Although Linux is a monolithic kernel, it can be extended using kernel modules. These are special objects that can be inserted into the kernel and removed on demand. In practical terms, kernel modules make it possible to add and remove drivers and interfaces that are not included in the kernel itself. Linux provides several commands for managing kernel modules.

28.1 Listing loaded modules with lsmod and modinfo

Use the lsmod command to view what kernel modules are currently loaded. The output of the command may look as follows:

> lsmod
Module                  Size  Used by
snd_usb_audio         188416  2
snd_usbmidi_lib        36864  1 snd_usb_audio
hid_plantronics        16384  0
snd_rawmidi            36864  1 snd_usbmidi_lib
snd_seq_device         16384  1 snd_rawmidi
fuse                  106496  3
nfsv3                  45056  1
nfs_acl                16384  1 nfsv3

The output is divided into three columns. The Module column lists the names of the loaded modules, while the Size column displays the size of each module. The Used by column shows the number of referring modules and their names. This list may be incomplete.

To view detailed information about a specific kernel module, use the modinfo MODULE_NAME command, where MODULE_NAME is the name of the desired kernel module. The modinfo binary resides in the /sbin directory that is not in the user's PATH environment variable. This means that you must specify the full path to the binary when running modinfo command as a regular user:

> /sbin/modinfo kvm
filename:       /lib/modules/6.4.0-150600.9-default/kernel/arch/x86/kvm/kvm.ko.zst
license:        GPL
author:         Qumranet
suserelease:    SLE15-SP6
srcversion:     9DACE73AC65F98D556DAD60
depends:        irqbypass
supported:      yes
retpoline:      Y
intree:         Y
name:           kvm
vermagic:       6.4.0-150600.9-default SMP mod_unload modversions

28.2 Adding and removing kernel modules

While it is possible to use insmod and rmmod to add and remove kernel modules, it is recommended to use the modprobe tool instead. modprobe offers several important advantages, including automatic dependency resolution and blacklisting.

When used without any parameters, the modprobe command installs a specified kernel module. modprobe must be run with root privileges:

> sudo modprobe acpi

To remove a kernel module, use the -r parameter:

> sudo modprobe -r acpi

28.2.1 Loading kernel modules automatically on boot

Instead of loading kernel modules manually, you can load them automatically during the boot process using the systemd-modules-load.service service. To enable a kernel module, add a .conf file to the /etc/modules-load.d/ directory. It is good practice to give the configuration file the same name as the module, for example:

/etc/modules-load.d/rt2800usb.conf

The configuration file must contain the name of the desired kernel module (for example, rt2800usb).

The described technique allows you to load kernel modules without any parameters. If you need to load a kernel module with specific options, add a configuration file to the /etc/modprobe.d/ directory instead. The file must have the .conf extension. The name of the file should adhere to the following naming convention: priority-modulename.conf, for example: 50-thinkfan.conf. The configuration file must contain the name of the kernel module and the desired parameters. You can use the example command below to create a configuration file containing the name of the kernel module and its parameters:

> echo "options thinkpad_acpi fan_control=1" | sudo tee /etc/modprobe.d/thinkfan.conf
Note
Note: Loading kernel modules

Most kernel modules are loaded by the system automatically when a device is detected or user space requests specific functionality. Thus, adding modules manually to /etc/modules-load.d/ is rarely required.

28.2.2 Blacklisting kernel modules with modprobe

Blacklisting a kernel module prevents it from loading during the boot process. This can be useful when you want to disable a module that you suspect is causing problems on your system. You can still load blacklisted kernel modules manually using the insmod or modprobe tools.

To blacklist a module, create a file /etc/modprobe.d/60-blacklist-MODULE_NAME.conf with the following content:

blacklist MODULE_NAME

Run the dracut command as root to generate a new initrd image, then reboot your machine (replace NAME with the name of the current initrd and KERNELVERSION with the currently running kernel):

> su
echo "blacklist nouveau" >> /etc/modprobe.d/60-blacklist-nouveau.conf
/usr/bin/dracut --logfile /var/log/YaST2/mkinitrd.log --force /boot/$initrd-NAME $KERNELVERSION
reboot

To disable a kernel module temporarily only, blacklist it on-the-fly during the boot. To do this, press the E key when you see the boot screen. This drops you into a minimal editor that allows you to modify boot parameters. Locate the line that looks as follows:

linux /boot/vmlinuz...splash= silent quiet showopts

Add the modprobe.blacklist=MODULE_NAME command to the end of the line. For example:

linux /boot/vmlinuz...splash= silent quiet showopts modprobe.blacklist=nouveau

Press F10 or CtrlX to boot with the specified configuration.

To blacklist a kernel module permanently via GRUB, open the /etc/default/grub file for editing, and add the modprobe.blacklist=MODULE_NAME option to the GRUB_CMDLINE_LINUX command. Then run the sudo grub2-mkconfig -o /boot/grub2/grub.cfg command to enable the changes.