Applies to SUSE Linux Enterprise Server 12 SP5

5 Kernel Probes #

Kernel probes are a set of tools to collect Linux kernel debugging and performance information. Developers and system administrators usually use them either to debug the kernel, or to find system performance bottlenecks. The reported data can then be used to tune the system for better performance.

You can insert these probes into any kernel routine, and specify a handler to be invoked after a particular break-point is hit. The main advantage of kernel probes is that you no longer need to rebuild the kernel and reboot the system after you make changes in a probe.

To use kernel probes, you typically need to write or obtain a specific kernel module. Such modules include both the init and the exit function. The init function (such as register_kprobe()) registers one or more probes, while the exit function unregisters them. The registration function defines where the probe will be inserted and which handler will be called after the probe is hit. To register or unregister a group of probes at one time, you can use relevant register_<PROBE_TYPE>probes() or unregister_<PROBE_TYPE>probes() functions.

Debugging and status messages are typically reported with the printk kernel routine. printk is a kernel space equivalent of a user space printf routine. For more information on printk, see Logging kernel messages. Normally, you can view these messages by inspecting the output of the systemd journal (see 第 15 章 “journalctl：查询 systemd 日记”). For more information on log files, see Chapter 3, Analyzing and Managing System Log Files.

5.1 Supported Architectures #

Kernel probes are fully implemented on the following architectures:

x86
AMD64/Intel 64
Arm
POWER

Kernel probes are partially implemented on the following architectures:

IA64 (does not support probes on instruction slot1)
sparc64 (return probes not yet implemented)

5.2 Types of Kernel Probes #

There are three types of kernel probes: Kprobes, Jprobes, and Kretprobes. Kretprobes are sometimes called return probes. You can find source code examples of all three type of probes in the Linux kernel. See the directory /usr/src/linux/samples/kprobes/ (package kernel-source).

5.2.1 Kprobes #

Kprobes can be attached to any instruction in the Linux kernel. When Kprobes is registered, it inserts a break-point at the first byte of the probed instruction. When the processor hits this break-point, the processor registers are saved, and the processing passes to Kprobes. First, a pre-handler is executed, then the probed instruction is stepped, and, finally a post-handler is executed. The control is then passed to the instruction following the probe point.

5.2.2 Jprobes #

Jprobes is implemented through the Kprobes mechanism. It is inserted on a function's entry point and allows direct access to the arguments of the function which is being probed. Its handler routine must have the same argument list and return value as the probed function. To end it, call the jprobe_return() function.

When a jprobe is hit, the processor registers are saved, and the instruction pointer is directed to the jprobe handler routine. The control then passes to the handler with the same register contents as the function being probed. Finally, the handler calls the jprobe_return() function, and switches the control back to the control function.

In general, you can insert multiple probes on one function. Jprobe is, however, limited to only one instance per function.

5.2.3 Return Probe #

Return probes are also implemented through Kprobes. When the register_kretprobe() function is called, a kprobe is attached to the entry of the probed function. After hitting the probe, the kernel probes mechanism saves the probed function return address and calls a user-defined return handler. The control is then passed back to the probed function.

Before you call register_kretprobe(), you need to set a maxactive argument, which specifies how many instances of the function can be probed at the same time. If set too low, you will miss a certain number of probes.

5.3 Kprobes API #

The programming interface of Kprobes consists of functions which are used to register and unregister all used kernel probes, and associated probe handlers. For a more detailed description of these functions and their arguments, see the information sources in Section 5.5, “For More Information”.

register_kprobe(): Inserts a break-point on a specified address. When the break-point is hit, the pre_handler and post_handler are called.
register_jprobe(): Inserts a break-point in the specified address. The address needs to be the address of the first instruction of the probed function. When the break-point is hit, the specified handler is run. The handler should have the same argument list and return type as the probed.
register_kretprobe(): Inserts a return probe for the specified function. When the probed function returns, a specified handler is run. This function returns 0 on success, or a negative error number on failure.
unregister_kprobe(), unregister_jprobe(), unregister_kretprobe(): Removes the specified probe. You can use it any time after the probe has been registered.
register_kprobes(), register_jprobes(), register_kretprobes(): Inserts each of the probes in the specified array.
unregister_kprobes(), unregister_jprobes(), unregister_kretprobes(): Removes each of the probes in the specified array.
disable_kprobe(), disable_jprobe(), disable_kretprobe(): Disables the specified probe temporarily.
enable_kprobe(), enable_jprobe(), enable_kretprobe(): Temporarily enables disabled probes.

5.4 `debugfs` Interface #

In recent Linux kernels, the Kprobes instrumentation uses the kernel's debugfs interface. It can list all registered probes and globally switch all probes on or off.

5.4.1 Listing Registered Kernel Probes #

The list of all currently registered probes is in the /sys/kernel/debug/kprobes/list file.

saturn.example.com:~ # cat /sys/kernel/debug/kprobes/list
c015d71a  k  vfs_read+0x0   [DISABLED]
c011a316  j  do_fork+0x0
c03dedc5  r  tcp_v4_rcv+0x0

The first column lists the address in the kernel where the probe is inserted. The second column prints the type of the probe: k for kprobe, j for jprobe, and r for return probe. The third column specifies the symbol, offset and optional module name of the probe. The following optional columns include the status information of the probe. If the probe is inserted on a virtual address which is not valid anymore, it is marked with [GONE]. If the probe is temporarily disabled, it is marked with [DISABLED].

5.4.2 How to Switch All Kernel Probes On or Off #

The /sys/kernel/debug/kprobes/enabled file represents a switch with which you can globally and forcibly turn on or off all the registered kernel probes. To turn them off, simply enter

echo "0" > /sys/kernel/debug/kprobes/enabled

on the command line as root. To turn them on again, enter

echo "1" > /sys/kernel/debug/kprobes/enabled

Note that this way you do not change the status of the probes. If a probe is temporarily disabled, it will not be enabled automatically but will remain in the [DISABLED] state after entering the latter command.

5.5 For More Information #

To learn more about kernel probes, look at the following sources of information:

Thorough but more technically oriented information about kernel probes is in /usr/src/linux/Documentation/kprobes.txt (package kernel-source).
Examples of all three types of probes (together with related Makefile) are in the /usr/src/linux/samples/kprobes/ directory (package kernel-source).
In-depth information about Linux kernel modules and printk kernel routine can be found at The Linux Kernel Module Programming Guide
Practical but slightly outdated information about the use of kernel probes can be found in Kernel debugging with Kprobes