Jump to contentJump to page navigation: previous page [access key p]/next page [access key n]
documentation.suse.com / SUSE Linux Enterprise Desktop Documentation / Administration Guide / Booting a Linux system / Introduction to the boot process
Applies to SUSE Linux Enterprise Desktop 15 SP5

16 Introduction to the boot process

  

Booting a Linux system involves different components and tasks. After a firmware and hardware initialization process, which depends on the machine's architecture, the kernel is started by means of the boot loader GRUB 2. After this point, the boot process is completely controlled by the operating system and handled by systemd. systemd provides a set of “targets” that boot configurations for everyday usage, maintenance or emergencies.

16.1 Terminology

  

This chapter uses terms that can be interpreted ambiguously. To understand how they are used here, read the definitions below:

init

Two different processes are commonly named “init”:

  • The initramfs process mounting the root file system

  • The operating system process that starts all other processes that is executed from the real root file system

In both cases, the systemd program is taking care of this task. It is first executed from the initramfs to mount the root file system. When that has succeeded, it is re-executed from the root file system as the initial process. To avoid confusing these two systemd processes, we refer to the first process as init on initramfs and to the second one as systemd.

initrd/initramfs

An initrd (initial RAM disk) is an image file containing a root file system image which is loaded by the kernel and mounted from /dev/ram as the temporary root file system. Mounting this file system requires a file system driver.

Beginning with kernel 2.6.13, the initrd has been replaced by the initramfs (initial RAM file system), which does not require a file system driver to be mounted. SUSE Linux Enterprise Desktop exclusively uses an initramfs. However, since the initramfs is stored as /boot/initrd, it is often called “initrd”. In this chapter we exclusively use the name initramfs.

16.2 The Linux boot process

  

The Linux boot process consists of several stages, each represented by a different component:

  1. Section 16.2.1, “The initialization and boot loader phase”

  2. Section 16.2.2, “The kernel phase”

  3. Section 16.2.3, “The init on initramfs phase”

  4. Section 16.2.4, “The systemd phase”

16.2.1 The initialization and boot loader phase

  

During the initialization phase the machine's hardware is set up and the devices are prepared. This process differs significantly between hardware architectures.

SUSE Linux Enterprise Desktop uses the boot loader GRUB 2 on all architectures. Depending on the architecture and firmware, starting the GRUB 2 boot loader can be a multi-step process. The purpose of the boot loader is to load the kernel and the initial, RAM-based file system (initramfs). For more information about GRUB 2, refer to Chapter 18, The boot loader GRUB 2.

16.2.1.1 Initialization and boot loader phase on AArch64 and AMD64/Intel 64

  

After turning on the computer, the BIOS or the UEFI initializes the screen and keyboard, and tests the main memory. Up to this stage, the machine does not access any mass storage media. Subsequently, the information about the current date, time, and the most important peripherals are loaded from the CMOS values. When the boot media and its geometry are recognized, the system control passes from the BIOS/UEFI to the boot loader.

On a machine equipped with a traditional BIOS, only code from the first physical 512-byte data sector (the Master Boot Record, MBR) of the boot disk can be loaded. Only a minimal GRUB 2 fits into the MBR. Its sole purpose is to load a GRUB 2 core image containing file system drivers from the gap between the MBR and the first partition (MBR partition table) or from the BIOS boot partition (GPT partition table). This image contains file system drivers and therefore is able to access /boot located on the root file system. /boot contains additional modules for GRUB 2 core as well as the kernel and the initramfs image. When it has access to this partition, GRUB 2 loads the kernel and the initramfs image into memory and hands control over to the kernel.

When booting a BIOS system from an encrypted file system that includes an encrypted /boot partition, you need to enter the password for decryption twice. It is first needed by GRUB 2 to decrypt /boot and then for systemd to mount the encrypted volumes.

On machines with UEFI the boot process is much simpler than on machines with a traditional BIOS. The firmware is able to read from a FAT formatted system partition of disks with a GPT partition table. This EFI system-partition (in the running system mounted as /boot/efi) holds enough space to host a fully-fledged GRUB 2 which is directly loaded and executed by the firmware.

If the BIOS/UEFI supports network booting, it is also possible to configure a boot server that provides the boot loader. The system can then be booted via PXE. The BIOS/UEFI acts as the boot loader. It gets the boot image from the boot server and starts the system. This is completely independent of local hard disks.

16.2.1.2 Initialization and boot loader phase on IBM Z

  

On IBM Z the boot process must be initialized by a boot loader called zipl (z initial program load). Although zipl supports reading from various file systems, it does not support the SLE default file system (Btrfs) or booting from snapshots. SUSE Linux Enterprise Desktop therefore uses a two-stage boot process that ensures full Btrfs support at boot-time:

  1. zipl boots from the partition /boot/zipl, which can be formatted with the Ext2, Ext3, Ext4, or XFS file system. This partition contains a minimal kernel and an initramfs that are loaded into memory. The initramfs contains a Btrfs driver (among others) and the boot loader GRUB 2. The kernel is started with a parameter initgrub, which tells it to start GRUB 2.

  2. The kernel mounts the root file system, so /boot becomes accessible. Now GRUB 2 is started from the initramfs. It reads its configuration from /boot/grub2/grub.cfg and loads the final kernel and initramfs from /boot. The new kernel now gets loaded via Kexec.

16.2.2 The kernel phase

  

When the boot loader has passed on system control, the boot process is the same on all architectures. The boot loader loads both the kernel and an initial RAM-based file system (initramfs) into memory and the kernel takes over.

After the kernel has set up memory management and has detected the CPU type and its features, it initializes the hardware and mounts the temporary root file system from the memory that was loaded with the initramfs.

16.2.2.1 The initramfs file

  

initramfs (initial RAM file system) is a small cpio archive that the kernel can load into a RAM disk. It is located at /boot/initrd. It can be created with a tool called dracut—refer to man 8 dracut for details.

The initramfs provides a minimal Linux environment that enables the execution of programs before the actual root file system is mounted. This minimal Linux environment is loaded into memory by BIOS or UEFI routines and does not have specific hardware requirements other than sufficient memory. The initramfs archive must always provide an executable named init that executes the systemd daemon on the root file system for the boot process to proceed.

Before the root file system can be mounted and the operating system can be started, the kernel needs the corresponding drivers to access the device on which the root file system is located. These drivers may include special drivers for certain kinds of hard disks or even network drivers to access a network file system. The needed modules for the root file system are loaded by init on initramfs. After the modules are loaded, udev provides the initramfs with the needed devices. Later in the boot process, after changing the root file system, it is necessary to regenerate the devices. This is done by the systemd unit systemd-udev-trigger.service.

16.2.2.1.1 Regenerating the initramfs
  

Because the initramfs contains drivers, it needs to be updated whenever a new version of one of its drivers is available. This is done automatically when installing the package containing the driver update. YaST or zypper will inform you about this by showing the output of the command that generates the initramfs. However, there are some occasions when you need to regenerate an initramfs manually:

Adding drivers because of hardware changes

If you need to change hardware, for example, hard disks, and this hardware requires different drivers to be in the kernel at boot time, you must update the initramfs file.

Open or create /etc/dracut.conf.d/10-DRIVER.conf and add the following line (mind the leading blank space): 

force_drivers+=" DRIVER1 "

Replace DRIVER1 with the module name of the driver. If you need to add more than one driver, list them space-separated: 

force_drivers+=" DRIVER1 DRIVER2 "

Proceed with Procedure 16.1, “Generate an initramfs”.

Moving system directories to a RAID or LVM

Whenever you move swap files, or system directories like /usr in a running system to a RAID or logical volume, you need to create an initramfs that contains support for software RAID or LVM drivers.

To do so, create the respective entries in /etc/fstab and mount the new entries (for example with mount -a and/or swapon -a).

Proceed with Procedure 16.1, “Generate an initramfs”.

Adding disks to an LVM group or Btrfs RAID containing the root file system

Whenever you add (or remove) a disk to a logical volume group or a Btrfs RAID containing the root file system, you need to create an initramfs that contains support for the enlarged volume. Follow the instructions at Procedure 16.1, “Generate an initramfs”.

Proceed with Procedure 16.1, “Generate an initramfs”.

Changing kernel variables

If you change the values of kernel variables via the sysctl interface by editing related files (/etc/sysctl.conf or /etc/sysctl.d/*.conf), the change will be lost on the next system reboot. Even if you load the values with sysctl --system at runtime, the changes are not saved into the initramfs file. You need to update it by proceeding as outlined in Procedure 16.1, “Generate an initramfs”.

Adding or removing swap devices, re-creating swap area

Whenever you add or remove a swap device, or re-create a swap area with a different UUID, update the initramfs as outlined in Procedure 16.1, “Generate an initramfs”. You may also need to update GRUB_CMDLINE_* variables that include the resume= option in /etc/default/grub, and then regenerate /boot/grub2/grub.cfg as outlined in Section 18.2.1, “The file /boot/grub2/grub.cfg”.

Procedure 16.1: Generate an initramfs
  

Note that all commands in the following procedure need to be executed as the root user.

  1. Enter your /boot directory: 

    # cd /boot

  2. Generate a new initramfs file with dracut, replacing MY_INITRAMFS with a file name of your choice: 

    # dracut MY_INITRAMFS

    Alternatively, run dracut -f FILENAME to replace an existing init file.

  3. (Skip this step if you ran dracut -f in the previous step.) Create a symbolic link from the initramfs file you created in the previous step to initrd: 

    #  ln -sf MY_INITRAMFS initrd

  4. On the IBM Z architecture, additionally run grub2-install.

16.2.3 The init on initramfs phase

  

The temporary root file system mounted by the kernel from the initramfs contains the executable systemd (which is called init on initramfs in the following, also see Section 16.1, “Terminology”. This program performs all actions needed to mount the proper root file system. It provides kernel functionality for the needed file system and device drivers for mass storage controllers with udev.

The main purpose of init on initramfs is to prepare the mounting of and access to the real root file system. Depending on your system configuration, init on initramfs is responsible for the following tasks.

Loading kernel modules

Depending on your hardware configuration, special drivers may be needed to access the hardware components of your computer (the most important component being your hard disk). To access the final root file system, the kernel needs to load the proper file system drivers.

Providing block special files

The kernel generates device events depending on loaded modules. udev handles these events and generates the required special block files on a RAM file system in /dev. Without those special files, the file system and other devices would not be accessible.

Managing RAID and LVM setups

If you configured your system to hold the root file system under RAID or LVM, init on initramfs sets up LVM or RAID to enable access to the root file system later.

Managing the network configuration

If you configured your system to use a network-mounted root file system (mounted via NFS), init must make sure that the proper network drivers are loaded and that they are set up to allow access to the root file system.

If the file system resides on a network block device like iSCSI or SAN, the connection to the storage server is also set up by init on initramfs. SUSE Linux Enterprise Desktop supports booting from a secondary iSCSI target if the primary target is not available. .

Note
Note: Handling of mount failures

If the root file system fails to mount from within the boot environment, it must be checked and repaired before the boot can continue. The file system checker will be automatically started for Ext3 and Ext4 file systems. The repair process is not automated for XFS and Btrfs file systems, and the user is presented with information describing the options available to repair the file system. When the file system has been successfully repaired, exiting the boot environment will cause the system to retry mounting the root file system. If successful, the boot will continue normally.

16.2.3.1 The init on initramfs phase in the installation process

  

When init on initramfs is called during the initial boot as part of the installation process, its tasks differ from those mentioned above. Note that the installation system also does not start systemd from initramfs—these tasks are performed by linuxrc.

Finding the installation medium

When starting the installation process, your machine loads an installation kernel and a special init containing the YaST installer. The YaST installer is running in a RAM file system and needs to have information about the location of the installation medium to access it for installing the operating system.

Initiating hardware recognition and loading appropriate kernel modules

As mentioned in Section 16.2.2.1, “The initramfs file”, the boot process starts with a minimum set of drivers that can be used with most hardware configurations. On AArch64, POWER, and AMD64/Intel 64 machines, linuxrc starts an initial hardware scanning process that determines the set of drivers suitable for your hardware configuration. On IBM Z, a list of drivers and their parameters needs to be provided, for example via linuxrc or a parmfile.

These drivers are used to generate a custom initramfs that is needed to boot the system. If the modules are not needed for boot but for coldplug, the modules can be loaded with systemd; for more information, see Section 19.6.4, “Loading kernel modules”.

Loading the installation system

When the hardware is properly recognized, the appropriate drivers are loaded. The udev program creates the special device files and linuxrc starts the installation system with the YaST installer.

Starting YaST

Finally, linuxrc starts YaST, which starts the package installation and the system configuration.

16.2.4 The systemd phase

  

After the “real” root file system has been found, it is checked for errors and mounted. If this is successful, the initramfs is cleaned and the systemd daemon on the root file system is executed. systemd is Linux's system and service manager. It is the parent process that is started as PID 1 and acts as an init system which brings up and maintains user space services. See Chapter 19, The systemd daemon for details.