Uyuni Proxy Setup
SUSE Manager Proxy requires additional configuration.
Check that the Proxy pattern is installed correctly.
This step is part of Install SUSE Manager Proxy with openSUSE Leap.
To verify a successful installation, on the server select the
pattern_uyuni_proxy package for installation.
The salt-broker service will be automatically started after installation is complete. This service forwards the Salt interactions to the SUSE Manager server.
It is possible to arrange Salt proxies in a chain.
In such a case, the upstream proxy is named
Make sure the TCP ports
4506 are open on the proxy.
The proxy must be able to reach the SUSE Manager Server or a parent proxy on these ports.
The proxy will share some SSL information with the SUSE Manager Server. Copy the certificate and its key from the SUSE Manager Server or the parent proxy.
As root, enter the following commands on the proxy using your SUSE Manager Server or parent Proxy (named
mkdir -m 700 /root/ssl-build cd /root/ssl-build scp root@PARENT:/root/ssl-build/RHN-ORG-PRIVATE-SSL-KEY . scp root@PARENT:/root/ssl-build/RHN-ORG-TRUSTED-SSL-CERT . scp root@PARENT:/root/ssl-build/rhn-ca-openssl.cnf .
To keep the security chain intact, the SUSE Manager Proxy functionality requires the SSL certificate to be signed by the same CA as the SUSE Manager Server certificate. Using certificates signed by different CAs for proxies and server is not supported.
configure-proxy.sh script finalizes the setup of your SUSE Manager Proxy.
Execute the interactive
Pressing Enter without further input will make the script use the default values provided between brackets
Here is some information about the requested settings:
- SUSE Manager Parent
The SUSE Manager parent can be either another proxy or the SUSE Manager Server.
- HTTP Proxy
A HTTP proxy enables your SUSE Manager proxy to access the Web. This is needed if direct access to the Web is prohibited by a firewall.
- Traceback Email
An email address where to report problems.
- Use SSL
For safety reasons, press
- Do You Want to Import Existing Certificates?
N. This ensures using the new certificates that were copied previously from the SUSE Manager server.
The next questions are about the characteristics to use for the SSL certificate of the proxy. The organization might be the same organization that was used on the server, unless of course your proxy is not in the same organization as your main server.
- Organization Unit
The default value here is the proxy’s hostname.
Further information attached to the proxy’s certificate.
Further information attached to the proxy’s certificate.
- Country Code
country codefield, enter the country code set during the SUSE Manager installation. For example, if your proxy is in the US and your SUSE Manager is in DE, enter
DEfor the proxy.
The country code must be two upper case letters. For a complete list of country codes, see https://www.iso.org/obp/ui/#search.
- Cname Aliases (Separated by Space)
Use this if your proxy can be accessed through various DNS CNAME aliases. Otherwise it can be left empty.
- CA Password
Enter the password that was used for the certificate of your SUSE Manager Server.
- Do You Want to Use an Existing SSH Key for Proxying SSH-Push Salt Minion?
Use this option if you want to reuse a SSH key that was used for SSH-Push Salt clients on the server.
- Create and Populate Configuration Channel rhn_proxy_config_1000010001?
- SUSE Manager Username
Use same user name and password as on the SUSE Manager server.
If parts are missing, such as CA key and public certificate, the script prints commands that you must execute to integrate the needed files.
When the mandatory files are copied, run
If you receive an HTTP error during script execution, run the script again.
configure-proxy.sh activates services required by SUSE Manager Proxy, such as
To check the status of the proxy system and its clients, click the proxy system’s details page on the Web UI (
Proxy subtabs display various status information.
To enable PXE boot through a proxy, additional software must be installed and configured on both the SUSE Manager Proxy and the SUSE Manager Server.
On the SUSE Manager Proxy, install the
zypper in susemanager-tftpsync-recv
On the SUSE Manager Proxy, run the
configure-tftpsync.shsetup script and enter the requested information:
You need to provide the hostname and IP address of the SUSE Manager Server and the proxy. You also need to enter the path to the tftpboot directory on the proxy.
On the SUSE Manager Server, install
zypper in susemanager-tftpsync
On the SUSE Manager Server, run
configure-tftpsync.sh. This creates the configuration, and uploads it to the SUSE Manager Proxy:
Start an initial synchronization on the SUSE Manager Server:
It can also be done after a change within Cobbler that needs to be synchronized immediately. Otherwise Cobbler synchronization will run automatically when needed. For more information about PXE booting, see Install via the Network.
SUSE Manager uses Cobbler for client provisioning. PXE (tftp) is installed and activated by default. Clients must be able to find the PXE boot on the SUSE Manager Proxy using DHCP. Use this DHCP configuration for the zone which contains the clients to be provisioned:
next-server: <IP_Address_of_Proxy> filename: "pxelinux.0"
A proxy does not contain any information about the clients that are connected to it. Therefore, a proxy can be replaced by a new one at any time. The replacement proxy must have the same name and IP address as its predecessor.
Shut down the old proxy, and leave it installed while you prepare the replacement. Create a reactivation key for this system and then register the new proxy using the reactivation key. If you do not use the reactivation key, you will need to re-register all the clients against the new proxy.
The reactivation key is only needed if you do not want to lose the history of the machine. If you do not use a reactivation key, the replacement proxy will become a "new" one with a new ID.
Before starting the actual migration procedure, save the data from the old proxy, if needed. Consider copying important or manually created data to a central place that can also be accessed by the new proxy.
Shut down the proxy.
Install a new SUSE Manager Proxy. For installation instructions, see Proxy Installation.
In the SUSE Manager Web UI, select the newly installed SUSE Manager Proxy, and delete it from the systems list.
In the Web UI, create a reactivation key for the old proxy system: On the System Details tab of the old proxy click
Generate New Key, and make a note of the new key, as you will need it later. For more information about reactivation keys, see Reactivation Keys.
OPTIONAL: After the installation of the new proxy, you might also need to:
Copy the centrally saved data to the new proxy system
Install any other needed software
Set up TFTP synchronization if the proxy is used for autoinstallation
During the installation of the proxy, clients will not be able to reach the SUSE Manager Server. After you have deleted a proxy, the systems list can be temporarily incorrect. All clients that were previously connected to the proxy will show as being directly connected to the server instead. After the first successful operation on a client, such as execution of a remote command or installation of a package or patch, this information will automatically be corrected. This may take some hours.